Skip to content

Decatur Fire and EMS Frequencies

We do not have frequencies listed specifically for Decatur in Adams County, Indiana yet. Countywide channels for Adams County that may also cover this area are shown below when we have them. The closest trunked radio site we have is Monroe (Indiana Project Hoosier SAFE-T), about 0 miles away.

About Decatur Fire and EMS Frequencies

Quick answer: County-level fire dispatch that covers Decatur: Adams County Fire 154.3700 MHz, narrow FM, 127.3 PL. Trunked: Indiana Project Hoosier SAFE-T, for example Adams County Fire talkgroup 10005 (hex 2715).

  • 2 conventional channels are analog FM, so any scanner can receive them. Enter the frequency and set the tone shown in the table.
  • Trunked radio systems that carry fire and EMS traffic here: Indiana Project Hoosier SAFE-T: 3 talkgroups. A trunking scanner is required, and it must support the system type shown.
  • To follow a trunked system, program a control channel first. For Decatur, start with the Monroe site of Indiana Project Hoosier SAFE-T, about 0 miles away. Its control channels: 853.4375, 853.9625 MHz.

Data updated .

Adams County channels that also cover Decatur

Fire Dispatch

Fire Dispatch frequencies for Adams County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Adams County FireFire/EMS Dispatch154.3700127.3 PLFMNWXL702
Adams County FireAdams County Fire – Mobile Repeater769.0063
In 799.0063
FMNWQPT256

Indiana Project Hoosier SAFE-T

Indiana Project Hoosier SAFE-T talkgroups
AgencyDescriptionTalkgroupHexMode
Adams County FireAdams County Fire – Dispatch (County)100052715D
Adams County EMSAdams County EMS – Dispatch (County)100042714D
Adams County HospitalEMS-to-Hospital ER (Operations 6)10013271dD

Nearest trunked radio sites

Distances are measured from the center of Decatur.

Monroe · Indiana Project Hoosier SAFE-T
RFSS 1 · Site 52 (hex 34) · NAC 6B2 · about 0 mi away
Control 853.4375, 853.9625
Voice 851.4625, 852.4, 852.9625
Bluffton · Indiana Project Hoosier SAFE-T
RFSS 1 · Site 51 (hex 33) · NAC 6BA · about 15 mi away
Control 858.9625, 859.9625
Voice 851.25, 851.775, 852.8875, 853.9125, 857.9625
Public Safety · Allen County P25
Project 25 · RFSS 1 · Site 1 (hex 1) · NAC 591 · about 17 mi away
Control 853.275, 853.3, 853.7625, 853.8375
Voice 851.325, 851.35, 851.5625, 851.5875, 851.7375, 851.825, 852.075, 852.1125, 852.1375, 852.3375, 852.7125, 852.7625, 852.8375, 853.15
What do these numbers mean?
Control channel
The frequency your scanner listens to first. It tells the scanner where each voice call is happening, so program it before anything else.
Voice
The other frequencies the site uses for calls. A trunking scanner follows them automatically once it has the control channel.
Site
One tower location of the system. Scanners show the number in decimal or hex, so both are listed.
RFSS (Radio Frequency Sub-System)
A group of sites run by the same controller. Large Project 25 systems can have several.
NAC (Network Access Code)
A hex code the site transmits. Your scanner can use it to ignore other systems on the same frequency.
Talkgroup
A virtual channel on a trunked system, such as one agency’s dispatch. Programming uses the decimal or hex number, depending on your scanner.

Common questions

What frequency does the fire department use in Decatur?

We do not have a fire dispatch channel listed specifically for Decatur. The county-level fire dispatch channels in the same county: Adams County Fire 154.3700 MHz, narrow FM, 127.3 PL.

Do fire departments and EMS use a trunked radio system in Decatur?

Yes. The county-level systems that cover Decatur are Fire and EMS talkgroups are listed for Indiana Project Hoosier SAFE-T: 3 talkgroups. A trunking scanner is required.

What scanner do I need to listen to fire and EMS in Decatur?

The analog conventional channels can be heard on any scanner; a trunking scanner is needed for the trunked talkgroups.

What are the control channels for trunked radio in Decatur?

For Decatur, start with the Monroe site of Indiana Project Hoosier SAFE-T. Its control channels are 853.4375, 853.9625 MHz. Program a control channel first; the scanner finds the voice channels from it.