Skip to content

Fairview Fire and EMS Frequencies

We do not have frequencies listed specifically for Fairview in Fayette County, Indiana yet. Countywide channels for Fayette County that may also cover this area are shown below when we have them. The closest trunked radio site we have is Connersville (Indiana Project Hoosier SAFE-T), about 7 miles away.

About Fairview Fire and EMS Frequencies

Quick answer: County-level fire dispatch that covers Fairview: Fayette County Fire 154.3550 MHz, narrow FM, 131.8 PL. Trunked: Indiana Project Hoosier SAFE-T, for example Fayette County Fire talkgroup 10234 (hex 27fa).

  • 1 conventional channel is analog FM, so any scanner can receive it. Enter the frequency and set the tone shown in the table.
  • Trunked radio systems that carry fire and EMS traffic here: Indiana Project Hoosier SAFE-T: 6 talkgroups. A trunking scanner is required, and it must support the system type shown.
  • To follow a trunked system, program a control channel first. For Fairview, start with the Connersville site of Indiana Project Hoosier SAFE-T, about 7 miles away. Its control channels: 851.8875, 852.3875, 853.725 MHz.

Data updated .

Fayette County channels that also cover Fairview

Fire Dispatch

Fire Dispatch frequencies for Fayette County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Fayette County FireFayette County Fire – Dispatch154.3550131.8 PLFMNKCK783

Indiana Project Hoosier SAFE-T

Indiana Project Hoosier SAFE-T talkgroups
AgencyDescriptionTalkgroupHexMode
Fayette County FireFayette County Fire – Dispatch (County)1023427faD
Fayette County FireFayette County Fire – Fire Ground (County)1023527fbD
Fayette County FireFayette County Fire – Fire Ground (County)1023627fcD
Fayette County FireFayette County Fire – Fire Ground (County)1023727fdD
Fayette County FireFayette County Fire – Fire Ground (County)1023827feD
Fayette County EMSFayette County EMS – Operations (County)1022827f4D

Nearest trunked radio sites

Distances are measured from the center of Fairview.

Connersville · Indiana Project Hoosier SAFE-T
RFSS 1 · Site 38 (hex 26) · NAC 6B8 · about 7 mi away
Control 851.8875, 852.3875, 853.725
Voice 851.2, 851.45
Rushville · Indiana Project Hoosier SAFE-T
RFSS 1 · Site 76 (hex 4C) · NAC 6B9 · about 10 mi away
Control 852.9625, 853.4625
Voice 851.4875, 851.9625, 852.4625
Knightstown · Indiana Project Hoosier SAFE-T
RFSS 1 · Site 94 (hex 5E) · NAC 6B4 · about 16 mi away
Control 774.43125, 774.68125
Voice 769.81875, 770.26875, 770.81875, 771.54375
What do these numbers mean?
Control channel
The frequency your scanner listens to first. It tells the scanner where each voice call is happening, so program it before anything else.
Voice
The other frequencies the site uses for calls. A trunking scanner follows them automatically once it has the control channel.
Site
One tower location of the system. Scanners show the number in decimal or hex, so both are listed.
RFSS (Radio Frequency Sub-System)
A group of sites run by the same controller. Large Project 25 systems can have several.
NAC (Network Access Code)
A hex code the site transmits. Your scanner can use it to ignore other systems on the same frequency.
Talkgroup
A virtual channel on a trunked system, such as one agency’s dispatch. Programming uses the decimal or hex number, depending on your scanner.

Common questions

What frequency does the fire department use in Fairview?

We do not have a fire dispatch channel listed specifically for Fairview. The county-level fire dispatch channels in the same county: Fayette County Fire 154.3550 MHz, narrow FM, 131.8 PL.

Do fire departments and EMS use a trunked radio system in Fairview?

Yes. The county-level systems that cover Fairview are Fire and EMS talkgroups are listed for Indiana Project Hoosier SAFE-T: 6 talkgroups. A trunking scanner is required.

What scanner do I need to listen to fire and EMS in Fairview?

The analog conventional channels can be heard on any scanner; a trunking scanner is needed for the trunked talkgroups.

What are the control channels for trunked radio in Fairview?

For Fairview, start with the Connersville site of Indiana Project Hoosier SAFE-T. Its control channels are 851.8875, 852.3875, 853.725 MHz. Program a control channel first; the scanner finds the voice channels from it.