Skip to content

Walnut Fire and EMS Frequencies

We do not have frequencies listed specifically for Walnut in Montgomery County, Indiana yet. Countywide channels for Montgomery County that may also cover this area are shown below when we have them. The closest trunked radio site we have is Crawfordsville (Indiana Project Hoosier SAFE-T), about 8 miles away.

About Walnut Fire and EMS Frequencies

Quick answer: County-level fire dispatch that covers Walnut: Emergency Management/Fire/EMS 155.8725 MHz, narrow FM, 162 DPL. Trunked: Indiana Project Hoosier SAFE-T, for example Montgomery County Fire talkgroup 11009 (hex 2b01).

  • 9 conventional channels are analog FM, so any scanner can receive them. Enter the frequency and set the tone shown in the table.
  • 2 conventional channels use a digital mode (DMR), which needs a scanner that decodes that mode.
  • Trunked radio systems that carry fire and EMS traffic here: Indiana Project Hoosier SAFE-T: 5 talkgroups. A trunking scanner is required, and it must support the system type shown.
  • To follow a trunked system, program a control channel first. For Walnut, start with the Crawfordsville site of Indiana Project Hoosier SAFE-T, about 8 miles away. Its control channels: 853.4625, 853.9875 MHz.

Data updated .

Montgomery County channels that also cover Walnut

Fire Dispatch

Fire Dispatch frequencies for Montgomery County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Emergency Management/Fire/EMSCounty Fire Dispatch – Whitesville Repeater155.8725
In 151.4825
162 DPLFMNKNDQ871
Emergency Management/Fire/EMSCounty Fire Dispatch – Cherry Grove Repeater158.8425
In 151.3325
174 DPLFMNKNDQ871

Fire Ground / Tactical

Fire Ground / Tactical frequencies for Montgomery County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Emergency Management/Fire/EMSWaynetown Fireground151.6250FMN—
Emergency Management/Fire/EMSCounty CERT Team154.0550FMNKNCG393
Emergency Management/Fire/EMSNW Montgomery Fire – Territory/Madison Township Fireground154.1750FMNWNAE325
Emergency Management/Fire/EMSWaynetown Fireground154.3100FMNKSF732
Emergency Management/Fire/EMSDarlington Fireground154.3250FMNKEY956
Emergency Management/Fire/EMSNW Montgomery Fire – Territory/Coal Creek Fireground154.3400FMNWQHI909
Emergency Management/Fire/EMSWalnut Township Fireground154.3550FMNKCY565
Emergency Management/Fire/EMSCounty EMA – Primary155.7225
In 158.8800
DMRWPCA497
Emergency Management/Fire/EMSCounty EMA – Backup453.3750
In 458.3750
DMRWPCA497

Indiana Project Hoosier SAFE-T

Indiana Project Hoosier SAFE-T talkgroups
AgencyDescriptionTalkgroupHexMode
Montgomery County FireMontgomery County Fire – Dispatch110092b01D
Montgomery County FireMontgomery County Fire – Fire Ground110102b02D
Montgomery County FireMontgomery County Fire – Fire Ground110112b03D
Montgomery County FireMontgomery County Fire – Fire Ground110122b04D
Montgomery County FireMontgomery County Fire – Fire Ground110132b05D

Nearest trunked radio sites

Distances are measured from the center of Walnut.

Crawfordsville · Indiana Project Hoosier SAFE-T
RFSS 1 · Site 68 (hex 44) · NAC 6BC · about 8 mi away
Control 853.4625, 853.9875
Voice 851.4875, 851.8875, 852.4125, 852.9375, 853.7625, 858.0625, 859.4875
Boone Co Simulcast · Indiana Project Hoosier SAFE-T
RFSS 1 · Site 3 (hex 3) · NAC 6B3 · about 16 mi away
Control 851.7375, 852.1625
Voice 851.2625, 851.4375, 852.525, 852.625, 853.175, 853.7375
Bainbridge · Indiana Project Hoosier SAFE-T
RFSS 1 · Site 81 (hex 51) · NAC 6B1 · about 17 mi away
Control 853.0625, 854.3875
Voice 851.3875, 851.8625, 852.2
What do these numbers mean?
Control channel
The frequency your scanner listens to first. It tells the scanner where each voice call is happening, so program it before anything else.
Voice
The other frequencies the site uses for calls. A trunking scanner follows them automatically once it has the control channel.
Site
One tower location of the system. Scanners show the number in decimal or hex, so both are listed.
RFSS (Radio Frequency Sub-System)
A group of sites run by the same controller. Large Project 25 systems can have several.
NAC (Network Access Code)
A hex code the site transmits. Your scanner can use it to ignore other systems on the same frequency.
Talkgroup
A virtual channel on a trunked system, such as one agency’s dispatch. Programming uses the decimal or hex number, depending on your scanner.

Common questions

What frequency does the fire department use in Walnut?

We do not have a fire dispatch channel listed specifically for Walnut. The county-level fire dispatch channels in the same county: Emergency Management/Fire/EMS 155.8725 MHz, narrow FM, 162 DPL.

Do fire departments and EMS use a trunked radio system in Walnut?

Yes. The county-level systems that cover Walnut are Fire and EMS talkgroups are listed for Indiana Project Hoosier SAFE-T: 5 talkgroups. A trunking scanner is required.

What scanner do I need to listen to fire and EMS in Walnut?

The analog conventional channels can be heard on any scanner; a scanner that decodes DMR is needed for the digital conventional channels; a trunking scanner is needed for the trunked talkgroups.

What are the control channels for trunked radio in Walnut?

For Walnut, start with the Crawfordsville site of Indiana Project Hoosier SAFE-T. Its control channels are 853.4625, 853.9875 MHz. Program a control channel first; the scanner finds the voice channels from it.