Skip to content

Kimmell Fire and EMS Frequencies

We do not have frequencies listed specifically for Kimmell in Noble County, Indiana yet. Countywide channels for Noble County that may also cover this area are shown below when we have them. The closest trunked radio site we have is Ligonier (Indiana Project Hoosier SAFE-T), about 5 miles away.

About Kimmell Fire and EMS Frequencies

Quick answer: County-level fire dispatch that covers Kimmell: Noble County Fire 154.2200 MHz, narrow FM, 97.4 PL. County-level ems dispatch that covers Kimmell: Noble County EMS 155.3250 MHz, narrow FM, 91.5 PL. Trunked: Indiana Project Hoosier SAFE-T, for example Noble County Fire talkgroup 12100 (hex 2f44).

  • 2 conventional channels are analog FM, so any scanner can receive them. Enter the frequency and set the tone shown in the table.
  • Trunked radio systems that carry fire and EMS traffic here: Indiana Project Hoosier SAFE-T: 3 talkgroups. A trunking scanner is required, and it must support the system type shown.
  • To follow a trunked system, program a control channel first. For Kimmell, start with the Ligonier site of Indiana Project Hoosier SAFE-T, about 5 miles away. Its control channels: 853.4875, 855.2375 MHz.

Data updated .

Noble County channels that also cover Kimmell

Fire Dispatch

Fire Dispatch frequencies for Noble County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Noble County FireNoble County Fire – Dispatch154.220097.4 PLFMNKLO448

EMS Dispatch

EMS Dispatch frequencies for Noble County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Noble County EMSNoble County EMS – Dispatch155.3250
In 159.3700
91.5 PLFMNWPZN654

Indiana Project Hoosier SAFE-T

Indiana Project Hoosier SAFE-T talkgroups
AgencyDescriptionTalkgroupHexMode
Noble County FireNoble County Fire – Dispatch (County)121002f44D
Noble County FireNoble County Fire – Operations East (County)121012f45D
Noble County FireNoble County Fire – Operations West (County)121022f46D

Nearest trunked radio sites

Distances are measured from the center of Kimmell.

Ligonier · Indiana Project Hoosier SAFE-T
RFSS 1 · Site 43 (hex 2B) · NAC 6B3 · about 5 mi away
Control 853.4875, 855.2375
Voice 851.05, 851.4875, 852.2, 852.5375
North Webster · Indiana Project Hoosier SAFE-T
RFSS 1 · Site 41 (hex 29) · NAC 6B1 · about 10 mi away
Control 852.9875, 853.675
Voice 851.65, 852.175, 852.65
Kendallville · Indiana Project Hoosier SAFE-T
RFSS 1 · Site 20 (hex 14) · NAC 6BA · about 14 mi away
Control 853.9875, 857.2625
Voice 851.425, 851.9625, 852.475, 852.9
What do these numbers mean?
Control channel
The frequency your scanner listens to first. It tells the scanner where each voice call is happening, so program it before anything else.
Voice
The other frequencies the site uses for calls. A trunking scanner follows them automatically once it has the control channel.
Site
One tower location of the system. Scanners show the number in decimal or hex, so both are listed.
RFSS (Radio Frequency Sub-System)
A group of sites run by the same controller. Large Project 25 systems can have several.
NAC (Network Access Code)
A hex code the site transmits. Your scanner can use it to ignore other systems on the same frequency.
Talkgroup
A virtual channel on a trunked system, such as one agency’s dispatch. Programming uses the decimal or hex number, depending on your scanner.

Common questions

What frequency does the fire department use in Kimmell?

We do not have a fire dispatch channel listed specifically for Kimmell. The county-level fire dispatch channels in the same county: Noble County Fire 154.2200 MHz, narrow FM, 97.4 PL.

What frequency does EMS or the ambulance service use in Kimmell?

We do not have a EMS dispatch channel listed specifically for Kimmell. The county-level EMS dispatch channels in the same county: Noble County EMS 155.3250 MHz, narrow FM, 91.5 PL.

Do fire departments and EMS use a trunked radio system in Kimmell?

Yes. The county-level systems that cover Kimmell are Fire and EMS talkgroups are listed for Indiana Project Hoosier SAFE-T: 3 talkgroups. A trunking scanner is required.

What scanner do I need to listen to fire and EMS in Kimmell?

The analog conventional channels can be heard on any scanner; a trunking scanner is needed for the trunked talkgroups.

What are the control channels for trunked radio in Kimmell?

For Kimmell, start with the Ligonier site of Indiana Project Hoosier SAFE-T. Its control channels are 853.4875, 855.2375 MHz. Program a control channel first; the scanner finds the voice channels from it.