Skip to content

Madison Fire and EMS Frequencies

We do not have frequencies listed specifically for Madison in Pike County, Indiana yet. Countywide channels for Pike County that may also cover this area are shown below when we have them. The closest trunked radio site we have is Petersburg (Indiana Project Hoosier SAFE-T), about 4 miles away.

About Madison Fire and EMS Frequencies

Quick answer: County-level fire dispatch that covers Madison: Pike Co Fire/EMS - Dispatch 151.3700 MHz, narrow FM, 82.5 PL. Trunked: Indiana Project Hoosier SAFE-T, for example Pike County Fire talkgroup 21587 (hex 5453).

  • 5 conventional channels are analog FM, so any scanner can receive them. Enter the frequency and set the tone shown in the table.
  • 1 conventional channel uses a digital mode (NXDN48), which needs a scanner that decodes that mode.
  • Trunked radio systems that carry fire and EMS traffic here: Indiana Project Hoosier SAFE-T: 6 talkgroups. A trunking scanner is required, and it must support the system type shown.
  • To follow a trunked system, program a control channel first. For Madison, start with the Petersburg site of Indiana Project Hoosier SAFE-T, about 4 miles away. Its control channels: 852.975, 853.475 MHz.

Data updated .

Pike County channels that also cover Madison

Fire Dispatch

Fire Dispatch frequencies for Pike County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Pike Co Fire/EMS - DispatchPike Co Fire/EMS – Dispatch151.370082.5 PLFMNWNUK817

Fire Ground / Tactical

Fire Ground / Tactical frequencies for Pike County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Jefferson Twp Fire - OperationsJefferson Twp Fire – Operations154.340085.4 PLFMNKNBY316
Jefferson Twp Fire - OperationsJefferson Twp Fire – Operations (Digital)154.3400NXDN48KNBY316
Lockhart Twp Fire - OperationsLockhart Twp Fire – Operations154.2350118.8 PLFMNWNZZ251
Patoka Twp Fire - OperationsPatoka Twp Fire – Operations154.2500
In 158.9250
179.9 PLFMNWPMA459

EMS Tactical

EMS Tactical frequencies for Pike County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Pike Co EMS - OperationsPike Co EMS – Operations154.040082.5 PLFMNKUN492

Indiana Project Hoosier SAFE-T

Indiana Project Hoosier SAFE-T talkgroups
AgencyDescriptionTalkgroupHexMode
Pike County FirePike County Fire – Dispatch215875453D
Pike County FirePike County Fire – Fire Ground215885454D
Pike County FirePike County Fire – Fire Ground215895455D
Pike County FirePike County Fire – Fire Ground215905456D
Pike County EMSPike County EMS – Dispatch215855451D
Pike County EMSPike County EMS – Tactical Channel215865452D

Nearest trunked radio sites

Distances are measured from the center of Madison.

Petersburg · Indiana Project Hoosier SAFE-T
RFSS 2 · Site 22 (hex 16) · NAC 6B2 · about 4 mi away
Control 852.975, 853.475
Voice 851.475, 851.9375
Princeton · Indiana Project Hoosier SAFE-T
RFSS 2 · Site 69 (hex 45) · NAC 6B6 · about 7 mi away
Control 853.85, 858.9875
Voice 851.0375, 853.6, 858.7125
INDOC Carlisle · Indiana Project Hoosier SAFE-T
RFSS 2 · Site 81 (hex 51) · NAC 6BE · about 9 mi away
Control 857.2375
Voice 856.2375, 858.2375, 859.2375, 859.5375
What do these numbers mean?
Control channel
The frequency your scanner listens to first. It tells the scanner where each voice call is happening, so program it before anything else.
Voice
The other frequencies the site uses for calls. A trunking scanner follows them automatically once it has the control channel.
Site
One tower location of the system. Scanners show the number in decimal or hex, so both are listed.
RFSS (Radio Frequency Sub-System)
A group of sites run by the same controller. Large Project 25 systems can have several.
NAC (Network Access Code)
A hex code the site transmits. Your scanner can use it to ignore other systems on the same frequency.
Talkgroup
A virtual channel on a trunked system, such as one agency’s dispatch. Programming uses the decimal or hex number, depending on your scanner.

Common questions

What frequency does the fire department use in Madison?

We do not have a fire dispatch channel listed specifically for Madison. The county-level fire dispatch channels in the same county: Pike Co Fire/EMS - Dispatch 151.3700 MHz, narrow FM, 82.5 PL.

Do fire departments and EMS use a trunked radio system in Madison?

Yes. The county-level systems that cover Madison are Fire and EMS talkgroups are listed for Indiana Project Hoosier SAFE-T: 6 talkgroups. A trunking scanner is required.

What scanner do I need to listen to fire and EMS in Madison?

The analog conventional channels can be heard on any scanner; a scanner that decodes NXDN48 is needed for the digital conventional channels; a trunking scanner is needed for the trunked talkgroups.

What are the control channels for trunked radio in Madison?

For Madison, start with the Petersburg site of Indiana Project Hoosier SAFE-T. Its control channels are 852.975, 853.475 MHz. Program a control channel first; the scanner finds the voice channels from it.