About Walnut Fire and EMS Frequencies
Quick answer: County-level fire dispatch that covers Walnut: Butler County Fire 155.8200 MHz, narrow FM, 146.2 PL. Trunked: Kansas Statewide Interoperable Communication System (KSICS), for example Butler County Fire talkgroup 2269 (hex 8dd).
- 1 conventional channel is analog FM, so any scanner can receive it. Enter the frequency and set the tone shown in the table.
- Trunked radio systems that carry fire and EMS traffic here: Kansas Statewide Interoperable Communication System (KSICS): 21 talkgroups. A trunking scanner is required, and it must support the system type shown.
- To follow a trunked system, program a control channel first. For Walnut, start with the Butler County site of Kansas Statewide Interoperable Communication System (KSICS), about 14 miles away. Its control channels: 851.425, 851.7375 MHz.
Data updated .
Butler County channels that also cover Walnut
Fire Dispatch
| Agency | Description | Frequency (MHz) | Tone | Mode | FCC |
|---|---|---|---|---|---|
| Butler County Fire | Fire and EMS Page Out | 155.8200 In 158.8050 | 146.2 PL | FMN | KAO312 |
Kansas Statewide Interoperable Communication System (KSICS)
| Agency | Description | Talkgroup | Hex | Mode |
|---|---|---|---|---|
| Butler County Fire | Butler County Fire – Dispatch | 2269 | 8dd | D |
| Butler County Fire | Fire Event | 2270 | 8de | D |
| Butler County Fire | Fire Event | 2271 | 8df | D |
| Butler County Fire | Fire Event | 2272 | 8e0 | D |
| Butler County Fire | Fire Event | 2273 | 8e1 | D |
| Butler County Fire | Fire Event | 2274 | 8e2 | D |
| Butler County Fire | Fire Event | 2275 | 8e3 | D |
| Butler County Fire | Fire Event | 2276 | 8e4 | D |
| Butler County Fire | Fire Event | 2277 | 8e5 | D |
| Butler County Fire | 911 Emergency | 2279 | 8e7 | D |
| Butler County Fire | Atlanta Fire Operations | 2323 | 913 | D |
| Butler County Fire | Burns Fire Operations | 2334 | 91e | D |
| Butler County Fire | Refinery Fire Operations | 2364 | 93c | D |
| Butler County Fire | Fire and EMS All Call | 2425 | 979 | D |
| Butler County EMS | Butler County EMS – Dispatch | 2293 | 8f5 | D |
| Butler County EMS | EMS Division 1 Call Channel | 2294 | 8f6 | D |
| Butler County EMS | EMS Division 2 Call Channel | 2295 | 8f7 | D |
| Butler County EMS | Car-to-Car | 2297 | 8f9 | D |
| Butler County EMS | EMS Administration | 2296 | 8f8 | D |
| Butler County EMS | Susan B. Allen Memorial Hospital Emergency Room – Patient Reports | 2299 | 8fb | D |
| Butler County EMS | Kansas Medical Center Emergency Room – Patient Reports | 2300 | 8fc | D |
Nearest trunked radio sites
Distances are measured from the center of Walnut.
What do these numbers mean?
- Control channel
- The frequency your scanner listens to first. It tells the scanner where each voice call is happening, so program it before anything else.
- Voice
- The other frequencies the site uses for calls. A trunking scanner follows them automatically once it has the control channel.
- Site
- One tower location of the system. Scanners show the number in decimal or hex, so both are listed.
- RFSS (Radio Frequency Sub-System)
- A group of sites run by the same controller. Large Project 25 systems can have several.
- NAC (Network Access Code)
- A hex code the site transmits. Your scanner can use it to ignore other systems on the same frequency.
- Talkgroup
- A virtual channel on a trunked system, such as one agency’s dispatch. Programming uses the decimal or hex number, depending on your scanner.
Common questions
What frequency does the fire department use in Walnut?
We do not have a fire dispatch channel listed specifically for Walnut. The county-level fire dispatch channels in the same county: Butler County Fire 155.8200 MHz, narrow FM, 146.2 PL.
Do fire departments and EMS use a trunked radio system in Walnut?
Yes. The county-level systems that cover Walnut are Fire and EMS talkgroups are listed for Kansas Statewide Interoperable Communication System (KSICS): 21 talkgroups. A trunking scanner is required.
What scanner do I need to listen to fire and EMS in Walnut?
The analog conventional channels can be heard on any scanner; a trunking scanner is needed for the trunked talkgroups.
What are the control channels for trunked radio in Walnut?
For Walnut, start with the Butler County site of Kansas Statewide Interoperable Communication System (KSICS). Its control channels are 851.425, 851.7375 MHz. Program a control channel first; the scanner finds the voice channels from it.