Skip to content

Pioneer Fire and EMS Frequencies

We do not have frequencies listed specifically for Pioneer in Graham County, Kansas yet. Countywide channels for Graham County that may also cover this area are shown below when we have them. The closest trunked radio site we have is Zurich (Kansas Statewide Interoperable Communication System (KSICS)), about 19 miles away.

About Pioneer Fire and EMS Frequencies

Quick answer: County-level fire dispatch that covers Pioneer: Graham County Fire 453.5250 MHz, narrow FM, 127.3 PL. Trunked: Kansas Statewide Interoperable Communication System (KSICS), for example Graham County Fire talkgroup 1345 (hex 541).

  • 1 conventional channel is analog FM, so any scanner can receive it. Enter the frequency and set the tone shown in the table.
  • Trunked radio systems that carry fire and EMS traffic here: Kansas Statewide Interoperable Communication System (KSICS): 6 talkgroups. A trunking scanner is required, and it must support the system type shown.
  • To follow a trunked system, program a control channel first. For Pioneer, start with the Zurich site of Kansas Statewide Interoperable Communication System (KSICS), about 19 miles away. Its control channels: 852.1125, 852.4125 MHz.

Data updated .

Graham County channels that also cover Pioneer

Fire Dispatch

Fire Dispatch frequencies for Graham County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Graham County FireGraham County Fire – Dispatch (before KSICS)453.5250
In 458.5250
127.3 PLFMNKNFT985

Kansas Statewide Interoperable Communication System (KSICS)

Kansas Statewide Interoperable Communication System (KSICS) talkgroups
AgencyDescriptionTalkgroupHexMode
Graham County FireGraham County Fire – Dispatch1345541D
Graham County FireGraham County Fire – Tactical Channel1346542D
Graham County FireGraham County Fire – Tactical Channel1347543D
Graham County EMSGraham County EMS – Dispatch134253eD
Graham County EMSGraham County EMS – Tactical Channel134353fD
Graham County EMSGraham County EMS – Tactical Channel1344540D

Nearest trunked radio sites

Distances are measured from the center of Pioneer.

Zurich · Kansas Statewide Interoperable Communication System (KSICS)
RFSS 2 · Site 29 (hex 1D) · NAC 1BB · about 19 mi away
Control 852.1125, 852.4125
Voice 851.8, 852.75, 853.475, 853.9
Norton · Kansas Statewide Interoperable Communication System (KSICS)
RFSS 2 · Site 33 (hex 21) · about 24 mi away
Control 852.4875, 852.775
Voice 851.7125, 853.075, 853.425, 853.725
Morland · Kansas Statewide Interoperable Communication System (KSICS)
RFSS 2 · Site 32 (hex 20) · NAC 1B7 · about 26 mi away
Control 851.7375, 852.0625
Voice 851.425, 852.3875, 853.375, 853.675
What do these numbers mean?
Control channel
The frequency your scanner listens to first. It tells the scanner where each voice call is happening, so program it before anything else.
Voice
The other frequencies the site uses for calls. A trunking scanner follows them automatically once it has the control channel.
Site
One tower location of the system. Scanners show the number in decimal or hex, so both are listed.
RFSS (Radio Frequency Sub-System)
A group of sites run by the same controller. Large Project 25 systems can have several.
NAC (Network Access Code)
A hex code the site transmits. Your scanner can use it to ignore other systems on the same frequency.
Talkgroup
A virtual channel on a trunked system, such as one agency’s dispatch. Programming uses the decimal or hex number, depending on your scanner.

Common questions

What frequency does the fire department use in Pioneer?

We do not have a fire dispatch channel listed specifically for Pioneer. The county-level fire dispatch channels in the same county: Graham County Fire 453.5250 MHz, narrow FM, 127.3 PL.

Do fire departments and EMS use a trunked radio system in Pioneer?

Yes. The county-level systems that cover Pioneer are Fire and EMS talkgroups are listed for Kansas Statewide Interoperable Communication System (KSICS): 6 talkgroups. A trunking scanner is required.

What scanner do I need to listen to fire and EMS in Pioneer?

The analog conventional channels can be heard on any scanner; a trunking scanner is needed for the trunked talkgroups.

What are the control channels for trunked radio in Pioneer?

For Pioneer, start with the Zurich site of Kansas Statewide Interoperable Communication System (KSICS). Its control channels are 852.1125, 852.4125 MHz. Program a control channel first; the scanner finds the voice channels from it.