About The Highlands Fire and EMS Frequencies
Quick answer: County-level fire dispatch that covers The Highlands: Reno County Fire 154.3700 MHz, narrow FM, 162.2 PL. Trunked: Kansas Statewide Interoperable Communication System (KSICS), for example Reno County Fire talkgroup 2368 (hex 940).
- 3 conventional channels are analog FM, so any scanner can receive them. Enter the frequency and set the tone shown in the table.
- Trunked radio systems that carry fire and EMS traffic here: Kansas Statewide Interoperable Communication System (KSICS): 9 talkgroups. A trunking scanner is required, and it must support the system type shown.
- To follow a trunked system, program a control channel first. For The Highlands, start with the Hutchinson site of Kansas Statewide Interoperable Communication System (KSICS), about 6 miles away. Its control channels: 852.4625, 852.725, 852.975 MHz.
Data updated .
Reno County channels that also cover The Highlands
Fire Dispatch
| Agency | Description | Frequency (MHz) | Tone | Mode | FCC |
|---|---|---|---|---|---|
| Reno County Fire | Reno County Fire – Dispatch (Dispatch before KSICS) | 154.3700 In 153.7700 | 162.2 PL | FMN | KBG643 |
Fire Ground / Tactical
| Agency | Description | Frequency (MHz) | Tone | Mode | FCC |
|---|---|---|---|---|---|
| Reno County Fire | Reno County Fire – Fire Ground (Tactical 4 before KSICS) | 153.9500 | FMN | KDK662 | |
| Reno County Fire | Reno County Fire – Fire Ground (Tactical 3 before KSICS) | 154.4450 | CSQ | FMN | KDK662 |
Kansas Statewide Interoperable Communication System (KSICS)
| Agency | Description | Talkgroup | Hex | Mode |
|---|---|---|---|---|
| Reno County Fire | Fire and EMS Dispatch | 2368 | 940 | D |
| Reno County Fire | Fire and EMS Automated Dispatch | 2387 | 953 | D |
| Reno County Fire | Reno County Fire – Tactical Channel | 2381 | 94d | D |
| Reno County Fire | Reno County Fire – Tactical Channel | 2382 | 94e | D |
| Reno County Fire | Reno County Fire – Tactical Channel | 2383 | 94f | D |
| Reno County Fire | Reno County Fire – Tactical Channel | 2384 | 950 | D |
| Reno County EMS | Car-to-Car | 666 | 29a | D |
| Reno County EMS | EMS Medical | 667 | 29b | D |
| Reno County EMS | EMS Administration | 663 | 297 | D |
Nearest trunked radio sites
Distances are measured from the center of The Highlands.
What do these numbers mean?
- Control channel
- The frequency your scanner listens to first. It tells the scanner where each voice call is happening, so program it before anything else.
- Voice
- The other frequencies the site uses for calls. A trunking scanner follows them automatically once it has the control channel.
- Site
- One tower location of the system. Scanners show the number in decimal or hex, so both are listed.
- RFSS (Radio Frequency Sub-System)
- A group of sites run by the same controller. Large Project 25 systems can have several.
- NAC (Network Access Code)
- A hex code the site transmits. Your scanner can use it to ignore other systems on the same frequency.
- Talkgroup
- A virtual channel on a trunked system, such as one agency’s dispatch. Programming uses the decimal or hex number, depending on your scanner.
Common questions
What frequency does the fire department use in The Highlands?
We do not have a fire dispatch channel listed specifically for The Highlands. The county-level fire dispatch channels in the same county: Reno County Fire 154.3700 MHz, narrow FM, 162.2 PL.
Do fire departments and EMS use a trunked radio system in The Highlands?
Yes. The county-level systems that cover The Highlands are Fire and EMS talkgroups are listed for Kansas Statewide Interoperable Communication System (KSICS): 9 talkgroups. A trunking scanner is required.
What scanner do I need to listen to fire and EMS in The Highlands?
The analog conventional channels can be heard on any scanner; a trunking scanner is needed for the trunked talkgroups.
What are the control channels for trunked radio in The Highlands?
For The Highlands, start with the Hutchinson site of Kansas Statewide Interoperable Communication System (KSICS). Its control channels are 852.4625, 852.725, 852.975 MHz. Program a control channel first; the scanner finds the voice channels from it.