Skip to content

Beaver Fire and EMS Frequencies

We do not have frequencies listed specifically for Beaver in Scott County, Kansas yet. Countywide channels for Scott County that may also cover this area are shown below when we have them. The closest trunked radio site we have is Modoc (Kansas Statewide Interoperable Communication System (KSICS)), about 19 miles away.

About Beaver Fire and EMS Frequencies

Quick answer: County-level ems dispatch that covers Beaver: Scott County EMS 462.9500 MHz, narrow FM, no tone. Trunked: Kansas Statewide Interoperable Communication System (KSICS), for example Scott County Fire talkgroup 516 (hex 204).

  • 2 conventional channels are analog FM, so any scanner can receive them. Enter the frequency and set the tone shown in the table.
  • Trunked radio systems that carry fire and EMS traffic here: Kansas Statewide Interoperable Communication System (KSICS): 4 talkgroups. A trunking scanner is required, and it must support the system type shown.
  • To follow a trunked system, program a control channel first. For Beaver, start with the Modoc site of Kansas Statewide Interoperable Communication System (KSICS), about 19 miles away. Its control channels: 852.4625, 852.725 MHz.

Data updated .

Scott County channels that also cover Beaver

EMS Dispatch

EMS Dispatch frequencies for Scott County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Scott County EMSScott County EMS – Dispatch (before KSICS)462.9500
In 467.9500
FMNWYR533
Scott County EMSScott County EMS – Dispatch (before KSICS)462.9750
In 467.9750
FMNWYR533

Kansas Statewide Interoperable Communication System (KSICS)

Kansas Statewide Interoperable Communication System (KSICS) talkgroups
AgencyDescriptionTalkgroupHexMode
Scott County FireScott County Fire – Dispatch516204D
Scott County FireScott County Fire – Tactical Channel585249D
Scott County EMSScott County EMS – Dispatch57323dD
Scott County EMSScott County EMS – Tactical Channel57423eD

Nearest trunked radio sites

Distances are measured from the center of Beaver.

Modoc · Kansas Statewide Interoperable Communication System (KSICS)
RFSS 1 · Site 31 (hex 1F) · NAC 1B6 · about 19 mi away
Control 852.4625, 852.725
Voice 851.8375, 852.975, 853.4, 853.8625
Oakley · Kansas Statewide Interoperable Communication System (KSICS)
RFSS 2 · Site 42 (hex 2A) · NAC 1B6 · about 24 mi away
Control 852.4875, 852.775
Voice 851.7125, 853.075, 853.425, 853.725
Dighton · Kansas Statewide Interoperable Communication System (KSICS)
RFSS 1 · Site 29 (hex 1D) · NAC 1B1 · about 36 mi away
Control 852.1125, 852.4125
Voice 851.8, 852.75, 853.475, 853.9
What do these numbers mean?
Control channel
The frequency your scanner listens to first. It tells the scanner where each voice call is happening, so program it before anything else.
Voice
The other frequencies the site uses for calls. A trunking scanner follows them automatically once it has the control channel.
Site
One tower location of the system. Scanners show the number in decimal or hex, so both are listed.
RFSS (Radio Frequency Sub-System)
A group of sites run by the same controller. Large Project 25 systems can have several.
NAC (Network Access Code)
A hex code the site transmits. Your scanner can use it to ignore other systems on the same frequency.
Talkgroup
A virtual channel on a trunked system, such as one agency’s dispatch. Programming uses the decimal or hex number, depending on your scanner.

Common questions

What frequency does EMS or the ambulance service use in Beaver?

We do not have a EMS dispatch channel listed specifically for Beaver. The county-level EMS dispatch channels in the same county: Scott County EMS 462.9500 MHz, narrow FM, no tone.

Do fire departments and EMS use a trunked radio system in Beaver?

Yes. The county-level systems that cover Beaver are Fire and EMS talkgroups are listed for Kansas Statewide Interoperable Communication System (KSICS): 4 talkgroups. A trunking scanner is required.

What scanner do I need to listen to fire and EMS in Beaver?

The analog conventional channels can be heard on any scanner; a trunking scanner is needed for the trunked talkgroups.

What are the control channels for trunked radio in Beaver?

For Beaver, start with the Modoc site of Kansas Statewide Interoperable Communication System (KSICS). Its control channels are 852.4625, 852.725 MHz. Program a control channel first; the scanner finds the voice channels from it.