Skip to content

Elk Creek Fire and EMS Frequencies

We do not have frequencies listed specifically for Elk Creek in Spencer County, Kentucky yet. Countywide channels for Spencer County that may also cover this area are shown below when we have them. The closest trunked radio site we have is Jeptha Knob (Louisville Emergency Communications Network: MetroSafe), about 10 miles away.

About Elk Creek Fire and EMS Frequencies

Quick answer: County-level ems dispatch that covers Elk Creek: Spencer County EMS 151.4450 MHz, FM, 136.5 PL. Trunked: Indiana Project Hoosier SAFE-T, for example Spencer County Fire talkgroup 21640 (hex 5488).

  • 2 conventional channels are analog FM, so any scanner can receive them. Enter the frequency and set the tone shown in the table.
  • 1 conventional channel uses a digital mode (P25), which needs a scanner that decodes that mode.
  • Trunked radio systems that carry fire and EMS traffic here: Indiana Project Hoosier SAFE-T: 6 talkgroups. A trunking scanner is required, and it must support the system type shown.
  • To follow a trunked system, program a control channel first. For Elk Creek, start with the Jeptha Knob site of Louisville Emergency Communications Network: MetroSafe, about 10 miles away. Its control channels: 853.225, 853.875 MHz.

Data updated .

Spencer County channels that also cover Elk Creek

Fire Talk-around

Fire Talk-around frequencies for Spencer County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Mt. Eden FireMt. Eden Fire (Expired)155.2350186.2 PLFMKNBP441

EMS Dispatch

EMS Dispatch frequencies for Spencer County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Spencer County EMSSpencer County EMS – Dispatch151.4450
In 159.0600
136.5 PLFMWQVZ438
Spencer County EMSSpencer County EMS – Dispatch151.4450
In 159.0600
NAC 719P25WQVZ438

Indiana Project Hoosier SAFE-T

Indiana Project Hoosier SAFE-T talkgroups
AgencyDescriptionTalkgroupHexMode
Spencer County FireSpencer County Fire – Dispatch (Countywide)216405488D
Spencer County FireSpencer County Fire – Fire Ground (Countywide)216415489D
Spencer County FireSpencer County Fire – Fire Ground (Countywide)21642548aD
Spencer County FireSpencer County Fire – Fire Ground (Countywide)21643548bD
Spencer County EMSSpencer County EMS – Dispatch (Countywide)216395487D
Spencer County EMSSpencer County EMS – Car-to-Car (Countywide)216385486D

Nearest trunked radio sites

Distances are measured from the center of Elk Creek.

Jeptha Knob · Louisville Emergency Communications Network: MetroSafe
RFSS 1 · Site 3 (hex 3) · NAC 1A0 · about 10 mi away
Control 853.225, 853.875
Voice 851.475, 852.475, 852.95
New Bernheim · Louisville Emergency Communications Network: MetroSafe
RFSS 1 · Site 5 (hex 5) · NAC 1A5 · about 16 mi away
Control 852.3875, 853.125
Voice 851.6375, 851.8875, 852.1375, 854.3875
New Bernheim · KY SERVS
RFSS 3 · Site 32 (hex 20) · NAC 9C2 · about 18 mi away
Control 774.68125
Voice 771.64375, 771.94375, 773.63125
What do these numbers mean?
Control channel
The frequency your scanner listens to first. It tells the scanner where each voice call is happening, so program it before anything else.
Voice
The other frequencies the site uses for calls. A trunking scanner follows them automatically once it has the control channel.
Site
One tower location of the system. Scanners show the number in decimal or hex, so both are listed.
RFSS (Radio Frequency Sub-System)
A group of sites run by the same controller. Large Project 25 systems can have several.
NAC (Network Access Code)
A hex code the site transmits. Your scanner can use it to ignore other systems on the same frequency.
Talkgroup
A virtual channel on a trunked system, such as one agency’s dispatch. Programming uses the decimal or hex number, depending on your scanner.

Common questions

What frequency does EMS or the ambulance service use in Elk Creek?

We do not have a EMS dispatch channel listed specifically for Elk Creek. The county-level EMS dispatch channels in the same county: Spencer County EMS 151.4450 MHz, FM, 136.5 PL.

Do fire departments and EMS use a trunked radio system in Elk Creek?

Yes. The county-level systems that cover Elk Creek are Fire and EMS talkgroups are listed for Indiana Project Hoosier SAFE-T: 6 talkgroups. A trunking scanner is required.

What scanner do I need to listen to fire and EMS in Elk Creek?

The analog conventional channels can be heard on any scanner; a scanner that decodes P25 is needed for the digital conventional channels; a trunking scanner is needed for the trunked talkgroups.

What are the control channels for trunked radio in Elk Creek?

For Elk Creek, start with the Jeptha Knob site of Louisville Emergency Communications Network: MetroSafe. Its control channels are 853.225, 853.875 MHz. Program a control channel first; the scanner finds the voice channels from it.