Skip to content

Amo Fire and EMS Frequencies

We do not have frequencies listed specifically for Amo in Cottonwood County, Minnesota yet. Countywide channels for Cottonwood County that may also cover this area are shown below when we have them. The closest trunked radio site we have is Jeffers (Allied Radio Matrix for Emergency Response (ARMER)), about 7 miles away.

About Amo Fire and EMS Frequencies

Quick answer: County-level fire dispatch that covers Amo: Cottonwood County Fire 154.3250 MHz, narrow FM, 100.0 PL. Trunked: Allied Radio Matrix for Emergency Response (ARMER), for example Cottonwood County Fire talkgroup 30704 (hex 77f0).

  • 1 conventional channel is analog FM, so any scanner can receive it. Enter the frequency and set the tone shown in the table.
  • Trunked radio systems that carry fire and EMS traffic here: Allied Radio Matrix for Emergency Response (ARMER): 3 talkgroups. A trunking scanner is required, and it must support the system type shown.
  • To follow a trunked system, program a control channel first. For Amo, start with the Jeffers site of Allied Radio Matrix for Emergency Response (ARMER), about 7 miles away. Its control channels: 851.4, 858.9625 MHz.

Data updated .

Cottonwood County channels that also cover Amo

Fire Dispatch

Fire Dispatch frequencies for Cottonwood County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Cottonwood County FireWindom, Mt Lake, Jeffers, Storden, Westbrook Fire EMS Paging154.3250
In 159.4500
100.0 PLFMNKNHP864

Allied Radio Matrix for Emergency Response (ARMER)

Allied Radio Matrix for Emergency Response (ARMER) talkgroups
AgencyDescriptionTalkgroupHexMode
Cottonwood County FireCounty Fire EMS Dispatch3070477f0D
Cottonwood County HospitalWindom Area Hospital3070377efD
Cottonwood County HospitalWestbrook Hospital307207800D

Nearest trunked radio sites

Distances are measured from the center of Amo.

Jeffers · Allied Radio Matrix for Emergency Response (ARMER)
RFSS 2 · Site 34 (hex 22) · about 7 mi away
Control 851.4, 858.9625
Voice 852.225, 853.4, 859.9625
Windom · Allied Radio Matrix for Emergency Response (ARMER)
RFSS 2 · Site 30 (hex 1E) · about 11 mi away
Control 853.175, 857.2125
Voice 852.175, 855.4875, 856.7125
Mountain Lake · Allied Radio Matrix for Emergency Response (ARMER)
RFSS 2 · Site 35 (hex 23) · about 18 mi away
Control 857.2625, 858.2625
Voice 852.1, 853.125, 853.875
What do these numbers mean?
Control channel
The frequency your scanner listens to first. It tells the scanner where each voice call is happening, so program it before anything else.
Voice
The other frequencies the site uses for calls. A trunking scanner follows them automatically once it has the control channel.
Site
One tower location of the system. Scanners show the number in decimal or hex, so both are listed.
RFSS (Radio Frequency Sub-System)
A group of sites run by the same controller. Large Project 25 systems can have several.
NAC (Network Access Code)
A hex code the site transmits. Your scanner can use it to ignore other systems on the same frequency.
Talkgroup
A virtual channel on a trunked system, such as one agency’s dispatch. Programming uses the decimal or hex number, depending on your scanner.

Common questions

What frequency does the fire department use in Amo?

We do not have a fire dispatch channel listed specifically for Amo. The county-level fire dispatch channels in the same county: Cottonwood County Fire 154.3250 MHz, narrow FM, 100.0 PL.

Do fire departments and EMS use a trunked radio system in Amo?

Yes. The county-level systems that cover Amo are Fire and EMS talkgroups are listed for Allied Radio Matrix for Emergency Response (ARMER): 3 talkgroups. A trunking scanner is required.

What scanner do I need to listen to fire and EMS in Amo?

The analog conventional channels can be heard on any scanner; a trunking scanner is needed for the trunked talkgroups.

What are the control channels for trunked radio in Amo?

For Amo, start with the Jeffers site of Allied Radio Matrix for Emergency Response (ARMER). Its control channels are 851.4, 858.9625 MHz. Program a control channel first; the scanner finds the voice channels from it.