Skip to content

Marshall Fire and EMS Frequencies

We do not have frequencies listed specifically for Marshall in Mower County, Minnesota yet. Countywide channels for Mower County that may also cover this area are shown below when we have them. The closest trunked radio site we have is Elkton (Allied Radio Matrix for Emergency Response (ARMER)), about 4 miles away.

About Marshall Fire and EMS Frequencies

Quick answer: County-level ems dispatch that covers Marshall: Mower County EMS 155.2050 MHz, narrow FM, 141.3 PL. Trunked: Allied Radio Matrix for Emergency Response (ARMER), for example Mower County Fire talkgroup 22207 (hex 56bf).

  • 4 conventional channels are analog FM, so any scanner can receive them. Enter the frequency and set the tone shown in the table.
  • Trunked radio systems that carry fire and EMS traffic here: Allied Radio Matrix for Emergency Response (ARMER): 2 talkgroups. A trunking scanner is required, and it must support the system type shown.
  • To follow a trunked system, program a control channel first. For Marshall, start with the Elkton site of Allied Radio Matrix for Emergency Response (ARMER), about 4 miles away. Its control channels: 856.2375 MHz.

Data updated .

Mower County channels that also cover Marshall

Fire Ground / Tactical

Fire Ground / Tactical frequencies for Mower County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Mower County FireMower County Fire – Fire Ground (including Austin, Brownsdale, Lyle)154.145097.4 PLFMNWPMJ464
Mower County FireBrownsdale FIRE Department156.1425
In 153.9875
FMNWQNS579

EMS Dispatch

EMS Dispatch frequencies for Mower County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Mower County EMSGold Cross Ambulance155.2050141.3 PLFMN—

Hospitals & Medical

Hospitals & Medical frequencies for Mower County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Mower County HospitalAustin Medical Center155.3850136.5 PLFMNKNHB500

Allied Radio Matrix for Emergency Response (ARMER)

Allied Radio Matrix for Emergency Response (ARMER) talkgroups
AgencyDescriptionTalkgroupHexMode
Mower County FireMower County Fire – Dispatch2220756bfD
Mower County EMSMower County EMS – Dispatch2222656d2D

Nearest trunked radio sites

Distances are measured from the center of Marshall.

Elkton · Allied Radio Matrix for Emergency Response (ARMER)
RFSS 3 · Site 5 (hex 5) · about 4 mi away
Control 856.2375
Voice 852.1, 857.4375, 857.7125, 858.7125, 859.0875, 859.4375
Austin · Allied Radio Matrix for Emergency Response (ARMER)
RFSS 3 · Site 6 (hex 6) · about 11 mi away
Control 852.9625
Voice 851.7125, 851.9125, 852.125, 852.4875, 852.7875
LeRoy · Allied Radio Matrix for Emergency Response (ARMER)
RFSS 3 · Site 86 (hex 56) · about 15 mi away
Control 853.875
Voice 852.3875, 852.8875, 853.4875, 854.9625
What do these numbers mean?
Control channel
The frequency your scanner listens to first. It tells the scanner where each voice call is happening, so program it before anything else.
Voice
The other frequencies the site uses for calls. A trunking scanner follows them automatically once it has the control channel.
Site
One tower location of the system. Scanners show the number in decimal or hex, so both are listed.
RFSS (Radio Frequency Sub-System)
A group of sites run by the same controller. Large Project 25 systems can have several.
NAC (Network Access Code)
A hex code the site transmits. Your scanner can use it to ignore other systems on the same frequency.
Talkgroup
A virtual channel on a trunked system, such as one agency’s dispatch. Programming uses the decimal or hex number, depending on your scanner.

Common questions

What frequency does EMS or the ambulance service use in Marshall?

We do not have a EMS dispatch channel listed specifically for Marshall. The county-level EMS dispatch channels in the same county: Mower County EMS 155.2050 MHz, narrow FM, 141.3 PL.

Do fire departments and EMS use a trunked radio system in Marshall?

Yes. The county-level systems that cover Marshall are Fire and EMS talkgroups are listed for Allied Radio Matrix for Emergency Response (ARMER): 2 talkgroups. A trunking scanner is required.

What scanner do I need to listen to fire and EMS in Marshall?

The analog conventional channels can be heard on any scanner; a trunking scanner is needed for the trunked talkgroups.

What are the control channels for trunked radio in Marshall?

For Marshall, start with the Elkton site of Allied Radio Matrix for Emergency Response (ARMER). Its control channels are 856.2375 MHz. Program a control channel first; the scanner finds the voice channels from it.