Skip to content

Redpath Fire and EMS Frequencies

We do not have frequencies listed specifically for Redpath in Traverse County, Minnesota yet. Countywide channels for Traverse County that may also cover this area are shown below when we have them. The closest trunked radio site we have is Wheaton (Allied Radio Matrix for Emergency Response (ARMER)), about 11 miles away.

About Redpath Fire and EMS Frequencies

Quick answer: County-level fire dispatch that covers Redpath: Traverse County Fire 154.2800 MHz, narrow FM, no tone. Trunked: Allied Radio Matrix for Emergency Response (ARMER), for example Traverse County Fire talkgroup 26711 (hex 6857).

  • 4 conventional channels are analog FM, so any scanner can receive them. Enter the frequency and set the tone shown in the table.
  • Trunked radio systems that carry fire and EMS traffic here: Allied Radio Matrix for Emergency Response (ARMER): 6 talkgroups. A trunking scanner is required, and it must support the system type shown.
  • To follow a trunked system, program a control channel first. For Redpath, start with the Wheaton site of Allied Radio Matrix for Emergency Response (ARMER), about 11 miles away. Its control channels: 859.7625, 860.7625 MHz.

Data updated .

Traverse County channels that also cover Redpath

Fire Dispatch

Fire Dispatch frequencies for Traverse County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Traverse County FireTraverse County Fire – Paging154.2800
In 150.8050
FMNWPXA815
Traverse County FireTraverse County Fire – Paging154.9650FMNKNFM406
Traverse County FireTraverse County Fire – Paging155.0850
In 158.8650
179.9 PLFMNWNRZ764

Hospitals & Medical

Hospitals & Medical frequencies for Traverse County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Traverse County HospitalWheaton Community Hosp.155.3550151.4 PLFMNKRS324

Allied Radio Matrix for Emergency Response (ARMER)

Allied Radio Matrix for Emergency Response (ARMER) talkgroups
AgencyDescriptionTalkgroupHexMode
Traverse County FireTraverse County Fire – Dispatch – 155.085 – 154.280 VHF267116857D
Traverse County FireTraverse Fire(1)26718685eD
Traverse County FireTraverse Fire(2)26719685fD
Traverse County FireTraverse Fire(3)267206860D
Traverse County FireTraverse Fire(4)267236863D
Traverse County FireTraverse Fire(5)267246864D

Nearest trunked radio sites

Distances are measured from the center of Redpath.

Wheaton · Allied Radio Matrix for Emergency Response (ARMER)
RFSS 4 · Site 18 (hex 12) · NAC 40B · about 11 mi away
Control 859.7625, 860.7625
Voice 855.9625, 856.7625, 857.7625, 858.7625
Herman · Allied Radio Matrix for Emergency Response (ARMER)
RFSS 4 · Site 7 (hex 7) · NAC 408 · about 11 mi away
Control 857.4625, 859.4625
Voice 851.125, 855.4625, 856.9375, 858.4625, 860.4625
Nashua · Allied Radio Matrix for Emergency Response (ARMER)
RFSS 4 · Site 25 (hex 19) · NAC 40e · about 13 mi away
Control 852.4, 852.9
Voice 851.95, 853.5, 859.2625
What do these numbers mean?
Control channel
The frequency your scanner listens to first. It tells the scanner where each voice call is happening, so program it before anything else.
Voice
The other frequencies the site uses for calls. A trunking scanner follows them automatically once it has the control channel.
Site
One tower location of the system. Scanners show the number in decimal or hex, so both are listed.
RFSS (Radio Frequency Sub-System)
A group of sites run by the same controller. Large Project 25 systems can have several.
NAC (Network Access Code)
A hex code the site transmits. Your scanner can use it to ignore other systems on the same frequency.
Talkgroup
A virtual channel on a trunked system, such as one agency’s dispatch. Programming uses the decimal or hex number, depending on your scanner.

Common questions

What frequency does the fire department use in Redpath?

We do not have a fire dispatch channel listed specifically for Redpath. The county-level fire dispatch channels in the same county: Traverse County Fire 154.2800 MHz, narrow FM, no tone.

Do fire departments and EMS use a trunked radio system in Redpath?

Yes. The county-level systems that cover Redpath are Fire and EMS talkgroups are listed for Allied Radio Matrix for Emergency Response (ARMER): 6 talkgroups. A trunking scanner is required.

What scanner do I need to listen to fire and EMS in Redpath?

The analog conventional channels can be heard on any scanner; a trunking scanner is needed for the trunked talkgroups.

What are the control channels for trunked radio in Redpath?

For Redpath, start with the Wheaton site of Allied Radio Matrix for Emergency Response (ARMER). Its control channels are 859.7625, 860.7625 MHz. Program a control channel first; the scanner finds the voice channels from it.