About Long Creek Fire and EMS Frequencies
Quick answer: County-level fire dispatch that covers Long Creek: Pender County Fire 155.1450 MHz, narrow FM, 103.5 PL. Trunked: North Carolina VIPER, for example Pender County Fire talkgroup 36008 (hex 8ca8).
- 9 conventional channels are analog FM, so any scanner can receive them. Enter the frequency and set the tone shown in the table.
- Trunked radio systems that carry fire and EMS traffic here: North Carolina VIPER: 4 talkgroups. A trunking scanner is required, and it must support the system type shown.
- To follow a trunked system, program a control channel first. For Long Creek, start with the Burgaw site of North Carolina VIPER, about 9 miles away. Its control channels: 852.35, 853.2375 MHz.
Data updated .
Pender County channels that also cover Long Creek
Fire Dispatch
| Agency | Description | Frequency (MHz) | Tone | Mode | FCC |
|---|---|---|---|---|---|
| Pender County Fire | Pender County Fire – Dispatch – East | 155.1450 | 103.5 PL | FMN | WPRW570 |
| Pender County Fire | Pender County Fire – Dispatch – West | 155.7000 In 158.7900 | 103.5 PL | FMN | KDL874 |
Fire Ground / Tactical
| Agency | Description | Frequency (MHz) | Tone | Mode | FCC |
|---|---|---|---|---|---|
| Pender County Fire | Rocky Point Volunteer Fire Department "Private" Channel | 154.0700 | 103.5 PL | FMN | WPQJ818 |
| Pender County Fire | Pender County Fire – Tactical Channel | 154.7550 | 103.5 PL | FMN | KDL874 |
| Pender County Fire | Pender County Fire – Tactical Channel | 154.8600 | 103.5 PL | FMN | KDL874 |
| Pender County Fire | Pender County Fire – Tactical Channel | 155.4150 | 103.5 PL | FMN | KDL874 |
| Pender County Fire | Pender County Fire – Tactical Channel | 155.5950 | 103.5 PL | FMN | KDL874 |
| Pender County Fire | Pender County Fire – Tactical Channel | 155.9100 | 103.5 PL | FMN | KDL874 |
| Pender County Fire | Pender County Fire – Tactical Channel | 156.0300 | 103.5 PL | FMN | KDL874 |
North Carolina VIPER
| Agency | Description | Talkgroup | Hex | Mode |
|---|---|---|---|---|
| Pender County Fire | County Fire Dispatch | 36008 | 8ca8 | D |
| Pender County Fire | County Fire Tactical | 36009 | 8ca9 | D |
| Pender County EMS | County EMS Dispatch | 36006 | 8ca6 | D |
| Pender County EMS | County EMS / Transport Service | 36007 | 8ca7 | D |
Nearest trunked radio sites
Distances are measured from the center of Long Creek.
What do these numbers mean?
- Control channel
- The frequency your scanner listens to first. It tells the scanner where each voice call is happening, so program it before anything else.
- Voice
- The other frequencies the site uses for calls. A trunking scanner follows them automatically once it has the control channel.
- Site
- One tower location of the system. Scanners show the number in decimal or hex, so both are listed.
- RFSS (Radio Frequency Sub-System)
- A group of sites run by the same controller. Large Project 25 systems can have several.
- NAC (Network Access Code)
- A hex code the site transmits. Your scanner can use it to ignore other systems on the same frequency.
- Talkgroup
- A virtual channel on a trunked system, such as one agency’s dispatch. Programming uses the decimal or hex number, depending on your scanner.
Common questions
What frequency does the fire department use in Long Creek?
We do not have a fire dispatch channel listed specifically for Long Creek. The county-level fire dispatch channels in the same county: Pender County Fire 155.1450 MHz, narrow FM, 103.5 PL.
Do fire departments and EMS use a trunked radio system in Long Creek?
Yes. The county-level systems that cover Long Creek are Fire and EMS talkgroups are listed for North Carolina VIPER: 4 talkgroups. A trunking scanner is required.
What scanner do I need to listen to fire and EMS in Long Creek?
The analog conventional channels can be heard on any scanner; a trunking scanner is needed for the trunked talkgroups.
What are the control channels for trunked radio in Long Creek?
For Long Creek, start with the Burgaw site of North Carolina VIPER. Its control channels are 852.35, 853.2375 MHz. Program a control channel first; the scanner finds the voice channels from it.