About Barrie Fire and EMS Frequencies
Quick answer: County-level fire dispatch that covers Barrie: Colfax/Walcott Fire 155.1600 MHz, narrow FM, no tone; Richland County Fire 154.9800 MHz, TELM, no tone. Trunked: North Dakota Statewide Interoperable Radio Network (SIRN 20/20), for example Richland County Fire talkgroup 39206 (hex 9926).
- 1 conventional channel is analog FM, so any scanner can receive it. Enter the frequency and set the tone shown in the table.
- 1 conventional channel uses a digital mode (TELM), which needs a scanner that decodes that mode.
- Trunked radio systems that carry fire and EMS traffic here: North Dakota Statewide Interoperable Radio Network (SIRN 20/20): 9 talkgroups. A trunking scanner is required, and it must support the system type shown.
- To follow a trunked system, program a control channel first. For Barrie, start with the Kindred (ND) site of Allied Radio Matrix for Emergency Response (ARMER), about 6 miles away. Its control channels: 854.0625, 855.9625, 857.1375 MHz.
Data updated .
Richland County channels that also cover Barrie
Fire Dispatch
| Agency | Description | Frequency (MHz) | Tone | Mode | FCC |
|---|---|---|---|---|---|
| Colfax/Walcott Fire | Fire and Rescue | 155.1600 | FMN | WNQO858 | |
| Richland County Fire | County Fire Signaling | 154.9800 In 153.8000 | TELM | KRF529 |
North Dakota Statewide Interoperable Radio Network (SIRN 20/20)
| Agency | Description | Talkgroup | Hex | Mode |
|---|---|---|---|---|
| Richland County Fire | County Fire Dispatch North | 39206 | 9926 | T |
| Richland County Fire | County Fire Dispatch South | 39207 | 9927 | T |
| Richland County Fire | County Fire Operations | 39208 | 9928 | T |
| Richland County Fire | County Fire Operations | 39209 | 9929 | T |
| Richland County Fire | County Fire Operations | 39210 | 992a | T |
| Richland County Fire | County Fire Operations | 39211 | 992b | T |
| Richland County Fire | County Fire Operations | 39212 | 992c | T |
| Richland County Fire | County Fire Operations | 39213 | 992d | T |
| Richland County Hospital | St Francis Hospital Breckenridge MN | 39802 | 9b7a | T |
Nearest trunked radio sites
Distances are measured from the center of Barrie.
What do these numbers mean?
- Control channel
- The frequency your scanner listens to first. It tells the scanner where each voice call is happening, so program it before anything else.
- Voice
- The other frequencies the site uses for calls. A trunking scanner follows them automatically once it has the control channel.
- Site
- One tower location of the system. Scanners show the number in decimal or hex, so both are listed.
- RFSS (Radio Frequency Sub-System)
- A group of sites run by the same controller. Large Project 25 systems can have several.
- NAC (Network Access Code)
- A hex code the site transmits. Your scanner can use it to ignore other systems on the same frequency.
- Talkgroup
- A virtual channel on a trunked system, such as one agency’s dispatch. Programming uses the decimal or hex number, depending on your scanner.
Common questions
What frequency does the fire department use in Barrie?
We do not have a fire dispatch channel listed specifically for Barrie. The county-level fire dispatch channels in the same county: Colfax/Walcott Fire 155.1600 MHz, narrow FM, no tone; Richland County Fire 154.9800 MHz, TELM, no tone.
Do fire departments and EMS use a trunked radio system in Barrie?
Yes. The county-level systems that cover Barrie are Fire and EMS talkgroups are listed for North Dakota Statewide Interoperable Radio Network (SIRN 20/20): 9 talkgroups. A trunking scanner is required.
What scanner do I need to listen to fire and EMS in Barrie?
The analog conventional channels can be heard on any scanner; a scanner that decodes TELM is needed for the digital conventional channels; a trunking scanner is needed for the trunked talkgroups.
What are the control channels for trunked radio in Barrie?
For Barrie, start with the Kindred (ND) site of Allied Radio Matrix for Emergency Response (ARMER). Its control channels are 854.0625, 855.9625, 857.1375, 859.2375 MHz. Program a control channel first; the scanner finds the voice channels from it.