Skip to content

Danton Fire and EMS Frequencies

We do not have frequencies listed specifically for Danton in Richland County, North Dakota yet. Countywide channels for Richland County that may also cover this area are shown below when we have them. The closest trunked radio site we have is Hankinson (North Dakota Statewide Interoperable Radio Network (SIRN 20/20)), about 14 miles away.

About Danton Fire and EMS Frequencies

Quick answer: County-level fire dispatch that covers Danton: Colfax/Walcott Fire 155.1600 MHz, narrow FM, no tone; Richland County Fire 154.9800 MHz, TELM, no tone. Trunked: North Dakota Statewide Interoperable Radio Network (SIRN 20/20), for example Richland County Fire talkgroup 39206 (hex 9926).

  • 1 conventional channel is analog FM, so any scanner can receive it. Enter the frequency and set the tone shown in the table.
  • 1 conventional channel uses a digital mode (TELM), which needs a scanner that decodes that mode.
  • Trunked radio systems that carry fire and EMS traffic here: North Dakota Statewide Interoperable Radio Network (SIRN 20/20): 9 talkgroups. A trunking scanner is required, and it must support the system type shown.
  • To follow a trunked system, program a control channel first. For Danton, start with the Hankinson site of North Dakota Statewide Interoperable Radio Network (SIRN 20/20), about 14 miles away. Its control channels: 853.7625 MHz.

Data updated .

Richland County channels that also cover Danton

Fire Dispatch

Fire Dispatch frequencies for Richland County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Colfax/Walcott FireFire and Rescue155.1600FMNWNQO858
Richland County FireCounty Fire Signaling154.9800
In 153.8000
TELMKRF529

North Dakota Statewide Interoperable Radio Network (SIRN 20/20)

North Dakota Statewide Interoperable Radio Network (SIRN 20/20) talkgroups
AgencyDescriptionTalkgroupHexMode
Richland County FireCounty Fire Dispatch North392069926T
Richland County FireCounty Fire Dispatch South392079927T
Richland County FireCounty Fire Operations392089928T
Richland County FireCounty Fire Operations392099929T
Richland County FireCounty Fire Operations39210992aT
Richland County FireCounty Fire Operations39211992bT
Richland County FireCounty Fire Operations39212992cT
Richland County FireCounty Fire Operations39213992dT
Richland County HospitalSt Francis Hospital Breckenridge MN398029b7aT

Nearest trunked radio sites

Distances are measured from the center of Danton.

Hankinson · North Dakota Statewide Interoperable Radio Network (SIRN 20/20)
RFSS 1 · Site 82 (hex 52) · NAC A61 · about 14 mi away
Control 853.7625
Voice 853.3125, 853.5375
Wyndmere · North Dakota Statewide Interoperable Radio Network (SIRN 20/20)
RFSS 1 · Site 78 (hex 4E) · NAC A6D · about 17 mi away
Control 851.9625, 852.2375
Voice 851.7375
Colfax · North Dakota Statewide Interoperable Radio Network (SIRN 20/20)
RFSS 1 · Site 103 (hex 67) · NAC A64 · about 17 mi away
Control 853.7125
Voice 853.2625, 853.4875
What do these numbers mean?
Control channel
The frequency your scanner listens to first. It tells the scanner where each voice call is happening, so program it before anything else.
Voice
The other frequencies the site uses for calls. A trunking scanner follows them automatically once it has the control channel.
Site
One tower location of the system. Scanners show the number in decimal or hex, so both are listed.
RFSS (Radio Frequency Sub-System)
A group of sites run by the same controller. Large Project 25 systems can have several.
NAC (Network Access Code)
A hex code the site transmits. Your scanner can use it to ignore other systems on the same frequency.
Talkgroup
A virtual channel on a trunked system, such as one agency’s dispatch. Programming uses the decimal or hex number, depending on your scanner.

Common questions

What frequency does the fire department use in Danton?

We do not have a fire dispatch channel listed specifically for Danton. The county-level fire dispatch channels in the same county: Colfax/Walcott Fire 155.1600 MHz, narrow FM, no tone; Richland County Fire 154.9800 MHz, TELM, no tone.

Do fire departments and EMS use a trunked radio system in Danton?

Yes. The county-level systems that cover Danton are Fire and EMS talkgroups are listed for North Dakota Statewide Interoperable Radio Network (SIRN 20/20): 9 talkgroups. A trunking scanner is required.

What scanner do I need to listen to fire and EMS in Danton?

The analog conventional channels can be heard on any scanner; a scanner that decodes TELM is needed for the digital conventional channels; a trunking scanner is needed for the trunked talkgroups.

What are the control channels for trunked radio in Danton?

For Danton, start with the Hankinson site of North Dakota Statewide Interoperable Radio Network (SIRN 20/20). Its control channels are 853.7625 MHz. Program a control channel first; the scanner finds the voice channels from it.