Skip to content

Juniper Canyon Fire and EMS Frequencies

We do not have frequencies listed specifically for Juniper Canyon in Crook County, Oregon yet. Countywide channels for Crook County that may also cover this area are shown below when we have them. The closest trunked radio site we have is Powell Butte (Oregon State Radio Project), about 12 miles away.

About Juniper Canyon Fire and EMS Frequencies

Quick answer: County-level fire dispatch that covers Juniper Canyon: Crook County Fire 154.9650 MHz, narrow FM, 131.8 PL. Trunked: Oregon State Radio Project, for example Crook County Fire talkgroup 9129 (hex 23a9).

  • 2 conventional channels are analog FM, so any scanner can receive them. Enter the frequency and set the tone shown in the table.
  • Trunked radio systems that carry fire and EMS traffic here: Oregon State Radio Project: 2 talkgroups. A trunking scanner is required, and it must support the system type shown.
  • To follow a trunked system, program a control channel first. For Juniper Canyon, start with the Powell Butte site of Oregon State Radio Project, about 12 miles away. Its control channels: 769.45625, 769.71875, 770.21875 MHz.

Data updated .

Crook County channels that also cover Juniper Canyon

Fire Dispatch

Fire Dispatch frequencies for Crook County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Crook County FireFire/EMS Dispatch154.9650
In 155.5950
131.8 PLFMNKCK677

Fire Ground / Tactical

Fire Ground / Tactical frequencies for Crook County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Crook County FireCrook County Fire – Tactical Channel154.2350FMNWQEB632

Oregon State Radio Project

Oregon State Radio Project talkgroups
AgencyDescriptionTalkgroupHexMode
Crook County FireCrook Co Fire912923a9T
Crook County HospitalSt. Charles Hospital Prineville9071236fT

Nearest trunked radio sites

Distances are measured from the center of Juniper Canyon.

Powell Butte · Oregon State Radio Project
RFSS 24 · Site 24 (hex 18) · NAC 018 · about 12 mi away
Control 769.45625, 769.71875, 770.21875, 770.94375, 774.79375
Grizzly · Oregon State Radio Project
RFSS 17 · Site 17 (hex 11) · NAC 011 · about 19 mi away
Control 769.41875, 770.45625, 770.70625, 773.31875, 774.05625
Pine Mountain · Oregon State Radio Project
RFSS 23 · Site 23 (hex 17) · NAC 017 · about 28 mi away
Control 769.44375, 769.68125, 773.33125, 773.79375, 774.04375, 774.53125
What do these numbers mean?
Control channel
The frequency your scanner listens to first. It tells the scanner where each voice call is happening, so program it before anything else.
Voice
The other frequencies the site uses for calls. A trunking scanner follows them automatically once it has the control channel.
Site
One tower location of the system. Scanners show the number in decimal or hex, so both are listed.
RFSS (Radio Frequency Sub-System)
A group of sites run by the same controller. Large Project 25 systems can have several.
NAC (Network Access Code)
A hex code the site transmits. Your scanner can use it to ignore other systems on the same frequency.
Talkgroup
A virtual channel on a trunked system, such as one agency’s dispatch. Programming uses the decimal or hex number, depending on your scanner.

Common questions

What frequency does the fire department use in Juniper Canyon?

We do not have a fire dispatch channel listed specifically for Juniper Canyon. The county-level fire dispatch channels in the same county: Crook County Fire 154.9650 MHz, narrow FM, 131.8 PL.

Do fire departments and EMS use a trunked radio system in Juniper Canyon?

Yes. The county-level systems that cover Juniper Canyon are Fire and EMS talkgroups are listed for Oregon State Radio Project: 2 talkgroups. A trunking scanner is required.

What scanner do I need to listen to fire and EMS in Juniper Canyon?

The analog conventional channels can be heard on any scanner; a trunking scanner is needed for the trunked talkgroups.

What are the control channels for trunked radio in Juniper Canyon?

For Juniper Canyon, start with the Powell Butte site of Oregon State Radio Project. Its control channels are 769.45625, 769.71875, 770.21875, 770.94375 MHz. Program a control channel first; the scanner finds the voice channels from it.