Skip to content

Barnesdale Fire and EMS Frequencies

We do not have frequencies listed specifically for Barnesdale in Tillamook County, Oregon yet. Countywide channels for Tillamook County that may also cover this area are shown below when we have them. The closest trunked radio site we have is South Saddle Mountain (WCN (P25) Network), about 24 miles away.

About Barnesdale Fire and EMS Frequencies

Quick answer: County-level fire dispatch that covers Barnesdale: Tillamook County Fire 154.3550 MHz, narrow FM, 103.5 PL. County-level ems dispatch that covers Barnesdale: Tillamook County EMS 462.9500 MHz, narrow FM, no tone.

  • 13 conventional channels are analog FM, so any scanner can receive them. Enter the frequency and set the tone shown in the table.

Data updated .

Tillamook County channels that also cover Barnesdale

Fire Dispatch

Fire Dispatch frequencies for Tillamook County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Tillamook County FireTillamook County Fire – Dispatch154.3550
In 158.9700
103.5 PLFMNWPVK567

Fire Ground / Tactical

Fire Ground / Tactical frequencies for Tillamook County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Tillamook County FireTillamook County Fire – Tactical Channel153.8900FMN—
Tillamook County FireTillamook County Fire – Tactical Channel (Simplex)154.0400103.5 PLFMNWNGL831
Tillamook County FireTillamook County Fire – Tactical Channel (Simplex)154.0700103.5 PLFMN—
Tillamook County FireTillamook County Fire – Tactical Channel (Repeater)154.0850
In 158.8200
192.8 PLFMNWPVK567
Tillamook County FireTillamook County Fire – Tactical Channel154.1450FMN—
Tillamook County FireTillamook County Fire – Tactical Channel (Repeater)154.2500
In 158.7750
103.5 PLFMNWPQZ441
Tillamook County FireTillamook County Fire – Tactical Channel (Simplex)154.2800CSQFMNWPWQ716
Tillamook County FireTillamook County Fire – Tactical Channel (Simplex)154.4300103.5 PLFMNWPWQ716
Tillamook County FireTillamook County Fire – Tactical Channel154.8300FMN—
Tillamook County FireTillamook County Fire – Tactical Channel (Repeater)155.2650
In 158.9400
103.5 PLFMNWPVK567
Tillamook County FireTillamook County Fire – Tactical Channel (Repeater)155.7150
In 150.8050
103.5 PLFMNWPQZ441

EMS Dispatch

EMS Dispatch frequencies for Tillamook County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Tillamook County EMSTillamook County EMS – Dispatch462.9500
In 467.9500
FMN—

Nearest trunked radio sites

Distances are measured from the center of Barnesdale.

South Saddle Mountain · WCN (P25) Network
Project 25 · RFSS 1 · Site 1 (hex 1) · NAC 9A1 · about 24 mi away
Control 852.2, 852.45, 852.85, 853.175
Washington County Simulcast C · WCN (P25) Network
Project 25 · RFSS 1 · Site 2 (hex 2) · NAC 9A2 · about 29 mi away
Control 852.8875, 853.4125, 853.875, 855.2125
Portland West Simulcast · Oregon State Radio Project
RFSS 60 · Site 60 (hex 3C) · NAC 03C · about 36 mi away
Control 769.21875, 769.71875, 770.46875, 770.93125, 773.05625, 773.33125, 774.29375
What do these numbers mean?
Control channel
The frequency your scanner listens to first. It tells the scanner where each voice call is happening, so program it before anything else.
Voice
The other frequencies the site uses for calls. A trunking scanner follows them automatically once it has the control channel.
Site
One tower location of the system. Scanners show the number in decimal or hex, so both are listed.
RFSS (Radio Frequency Sub-System)
A group of sites run by the same controller. Large Project 25 systems can have several.
NAC (Network Access Code)
A hex code the site transmits. Your scanner can use it to ignore other systems on the same frequency.
Talkgroup
A virtual channel on a trunked system, such as one agency’s dispatch. Programming uses the decimal or hex number, depending on your scanner.

Common questions

What frequency does the fire department use in Barnesdale?

We do not have a fire dispatch channel listed specifically for Barnesdale. The county-level fire dispatch channels in the same county: Tillamook County Fire 154.3550 MHz, narrow FM, 103.5 PL.

What frequency does EMS or the ambulance service use in Barnesdale?

We do not have a EMS dispatch channel listed specifically for Barnesdale. The county-level EMS dispatch channels in the same county: Tillamook County EMS 462.9500 MHz, narrow FM, no tone.

What scanner do I need to listen to fire and EMS in Barnesdale?

The analog conventional channels can be heard on any scanner.

What are the control channels for trunked radio in Barnesdale?

For Barnesdale, start with the South Saddle Mountain site of WCN (P25) Network. Its control channels are 852.2, 852.45, 852.85, 853.175 MHz. Program a control channel first; the scanner finds the voice channels from it.