About Burbank Fire and EMS Frequencies
Quick answer: County-level fire dispatch that covers Burbank: Clay County Fire 155.9400 MHz, FM, 173.8 PL. Trunked: South Dakota State Radio System, for example Clay County Fire talkgroup 1356 (hex 54c).
- 4 conventional channels are analog FM, so any scanner can receive them. Enter the frequency and set the tone shown in the table.
- Trunked radio systems that carry fire and EMS traffic here: South Dakota State Radio System: 4 talkgroups. A trunking scanner is required, and it must support the system type shown.
- To follow a trunked system, program a control channel first. For Burbank, start with the Vermillion site of South Dakota State Radio System, about 5 miles away. Its control channels: 157.2, 159.285 MHz.
Data updated .
Clay County channels that also cover Burbank
Fire Dispatch
| Agency | Description | Frequency (MHz) | Tone | Mode | FCC |
|---|---|---|---|---|---|
| Clay County Fire | Vermillion Fire-EMS-City Dispatch | 155.9400 In 154.9950 | 173.8 PL | FM | KRI494 |
Fire Ground / Tactical
| Agency | Description | Frequency (MHz) | Tone | Mode | FCC |
|---|---|---|---|---|---|
| Clay County Fire | Wakonda Fire-EMS | 154.2350 In 150.8050 | 123.0 PL | FM | WPMK709 |
| Clay County Fire | Vermillion Fire-EMS Tactical | 154.8150 In 158.7900 | 88.5 PL | FM | WPGA948 |
| Clay County Fire | Irene Fire-EMS | 155.0850 | 173.8 PL | FM | WPRF840 |
South Dakota State Radio System
| Agency | Description | Talkgroup | Hex | Mode |
|---|---|---|---|---|
| Clay County Fire | Clay County Fire – Dispatch | 1356 | 54c | D |
| Clay County Fire | Clay County Fire – Alternate | 1357 | 54d | D |
| Clay County EMS | Clay Co EMS | 1359 | 54f | D |
| Clay County Hospital | Dakota Hospital | 1361 | 551 | D |
Nearest trunked radio sites
Distances are measured from the center of Burbank.
What do these numbers mean?
- Control channel
- The frequency your scanner listens to first. It tells the scanner where each voice call is happening, so program it before anything else.
- Voice
- The other frequencies the site uses for calls. A trunking scanner follows them automatically once it has the control channel.
- Site
- One tower location of the system. Scanners show the number in decimal or hex, so both are listed.
- RFSS (Radio Frequency Sub-System)
- A group of sites run by the same controller. Large Project 25 systems can have several.
- NAC (Network Access Code)
- A hex code the site transmits. Your scanner can use it to ignore other systems on the same frequency.
- Talkgroup
- A virtual channel on a trunked system, such as one agency’s dispatch. Programming uses the decimal or hex number, depending on your scanner.
Common questions
What frequency does the fire department use in Burbank?
We do not have a fire dispatch channel listed specifically for Burbank. The county-level fire dispatch channels in the same county: Clay County Fire 155.9400 MHz, FM, 173.8 PL.
Do fire departments and EMS use a trunked radio system in Burbank?
Yes. The county-level systems that cover Burbank are Fire and EMS talkgroups are listed for South Dakota State Radio System: 4 talkgroups. A trunking scanner is required.
What scanner do I need to listen to fire and EMS in Burbank?
The analog conventional channels can be heard on any scanner; a trunking scanner is needed for the trunked talkgroups.
What are the control channels for trunked radio in Burbank?
For Burbank, start with the Vermillion site of South Dakota State Radio System. Its control channels are 157.2, 159.285 MHz. Program a control channel first; the scanner finds the voice channels from it.