Skip to content

Cleveland Fire and EMS Frequencies

We do not have frequencies listed specifically for Cleveland in Hamlin County, South Dakota yet. Countywide channels for Hamlin County that may also cover this area are shown below when we have them. The closest trunked radio site we have is De Smet (South Dakota State Radio System), about 18 miles away.

About Cleveland Fire and EMS Frequencies

Quick answer: County-level fire dispatch that covers Cleveland: Hamlin County Fire 154.4300 MHz, FM, 118.8 PL. Trunked: South Dakota State Radio System, for example Hamlin County Fire talkgroup 1307 (hex 51b).

  • 3 conventional channels are analog FM, so any scanner can receive them. Enter the frequency and set the tone shown in the table.
  • Trunked radio systems that carry fire and EMS traffic here: South Dakota State Radio System: 3 talkgroups. A trunking scanner is required, and it must support the system type shown.
  • To follow a trunked system, program a control channel first. For Cleveland, start with the De Smet site of South Dakota State Radio System, about 18 miles away. Its control channels: 159.015, 159.33, 159.885 MHz.

Data updated .

Hamlin County channels that also cover Cleveland

Fire Dispatch

Fire Dispatch frequencies for Hamlin County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Hamlin County FireCounty Fire154.4300
In 153.8300
118.8 PLFMWPCI995

Fire Ground / Tactical

Fire Ground / Tactical frequencies for Hamlin County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Hamlin County FireHazel Fire154.3250FMNWPRU674
Hamlin County FireHayti Fire154.3700FMNWPYL573

South Dakota State Radio System

South Dakota State Radio System talkgroups
AgencyDescriptionTalkgroupHexMode
Hamlin County FireHamlin County Fire – Dispatch130751bD
Hamlin County FireHamlin County Fire – Fire Ground130851cD
Hamlin County EMSHamlin County EMS – Dispatch130951dD

Nearest trunked radio sites

Distances are measured from the center of Cleveland.

De Smet · South Dakota State Radio System
RFSS 1 · Site 8 (hex 8) · NAC 478 · about 18 mi away
Control 159.015, 159.33, 159.885
Voice 160.2
Watertown · South Dakota State Radio System
RFSS 1 · Site 41 (hex 29) · NAC 477 · about 22 mi away
Control 157.89, 158.67
Voice 158.01, 158.52
Brookings · South Dakota State Radio System
RFSS 1 · Site 39 (hex 27) · NAC 475 · about 32 mi away
Control 157.92, 158.04
Voice 157.8, 158.61
What do these numbers mean?
Control channel
The frequency your scanner listens to first. It tells the scanner where each voice call is happening, so program it before anything else.
Voice
The other frequencies the site uses for calls. A trunking scanner follows them automatically once it has the control channel.
Site
One tower location of the system. Scanners show the number in decimal or hex, so both are listed.
RFSS (Radio Frequency Sub-System)
A group of sites run by the same controller. Large Project 25 systems can have several.
NAC (Network Access Code)
A hex code the site transmits. Your scanner can use it to ignore other systems on the same frequency.
Talkgroup
A virtual channel on a trunked system, such as one agency’s dispatch. Programming uses the decimal or hex number, depending on your scanner.

Common questions

What frequency does the fire department use in Cleveland?

We do not have a fire dispatch channel listed specifically for Cleveland. The county-level fire dispatch channels in the same county: Hamlin County Fire 154.4300 MHz, FM, 118.8 PL.

Do fire departments and EMS use a trunked radio system in Cleveland?

Yes. The county-level systems that cover Cleveland are Fire and EMS talkgroups are listed for South Dakota State Radio System: 3 talkgroups. A trunking scanner is required.

What scanner do I need to listen to fire and EMS in Cleveland?

The analog conventional channels can be heard on any scanner; a trunking scanner is needed for the trunked talkgroups.

What are the control channels for trunked radio in Cleveland?

For Cleveland, start with the De Smet site of South Dakota State Radio System. Its control channels are 159.015, 159.33, 159.885 MHz. Program a control channel first; the scanner finds the voice channels from it.