Skip to content

Gilbert Fire and EMS Frequencies

We do not have frequencies listed specifically for Gilbert in Hand County, South Dakota yet. Countywide channels for Hand County that may also cover this area are shown below when we have them. The closest trunked radio site we have is Redfield (South Dakota State Radio System), about 24 miles away.

About Gilbert Fire and EMS Frequencies

Quick answer: County-level fire dispatch that covers Gilbert: Hand County Fire 460.7000 MHz, narrow FM, 146.2 PL. Trunked: South Dakota State Radio System, for example Hand County Fire talkgroup 1430 (hex 596).

  • 3 conventional channels are analog FM, so any scanner can receive them. Enter the frequency and set the tone shown in the table.
  • Trunked radio systems that carry fire and EMS traffic here: South Dakota State Radio System: 1 talkgroup. A trunking scanner is required, and it must support the system type shown.
  • To follow a trunked system, program a control channel first. For Gilbert, start with the Redfield site of South Dakota State Radio System, about 24 miles away. Its control channels: 155.415 MHz.

Data updated .

Hand County channels that also cover Gilbert

Fire Dispatch

Fire Dispatch frequencies for Hand County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Hand County FireHand County Fire – South repeater460.7000
In 465.7000
146.2 PLFMNWPGS205
Hand County FireOrient-Polo Fire461.6000
In 466.6000
88.5 PLFMNWQFY895
Hand County FireWessington Fire & EMS463.4000
In 468.4000
664 DPLFMNWPDV377

South Dakota State Radio System

South Dakota State Radio System talkgroups
AgencyDescriptionTalkgroupHexMode
Hand County FireHand County Fire – Dispatch1430596D

Nearest trunked radio sites

Distances are measured from the center of Gilbert.

Redfield · South Dakota State Radio System
RFSS 1 · Site 60 (hex 3C) · about 24 mi away
Control 155.415
Voice 156.12, 159.69
Miller · South Dakota State Radio System
RFSS 1 · Site 10 (hex A) · NAC 47A · about 24 mi away
Control 155.58, 159.27
Voice 159.03, 159.465, 160.065
Orient Hills · South Dakota State Radio System
RFSS 1 · Site 47 (hex 2F) · about 27 mi away
Control 158.49, 158.64
Voice 157.83, 157.95
What do these numbers mean?
Control channel
The frequency your scanner listens to first. It tells the scanner where each voice call is happening, so program it before anything else.
Voice
The other frequencies the site uses for calls. A trunking scanner follows them automatically once it has the control channel.
Site
One tower location of the system. Scanners show the number in decimal or hex, so both are listed.
RFSS (Radio Frequency Sub-System)
A group of sites run by the same controller. Large Project 25 systems can have several.
NAC (Network Access Code)
A hex code the site transmits. Your scanner can use it to ignore other systems on the same frequency.
Talkgroup
A virtual channel on a trunked system, such as one agency’s dispatch. Programming uses the decimal or hex number, depending on your scanner.

Common questions

What frequency does the fire department use in Gilbert?

We do not have a fire dispatch channel listed specifically for Gilbert. The county-level fire dispatch channels in the same county: Hand County Fire 460.7000 MHz, narrow FM, 146.2 PL.

Do fire departments and EMS use a trunked radio system in Gilbert?

Yes. The county-level systems that cover Gilbert are Fire and EMS talkgroups are listed for South Dakota State Radio System: 1 talkgroup. A trunking scanner is required.

What scanner do I need to listen to fire and EMS in Gilbert?

The analog conventional channels can be heard on any scanner; a trunking scanner is needed for the trunked talkgroups.

What are the control channels for trunked radio in Gilbert?

For Gilbert, start with the Redfield site of South Dakota State Radio System. Its control channels are 155.415 MHz. Program a control channel first; the scanner finds the voice channels from it.