Skip to content

Marlar Fire and EMS Frequencies

We do not have frequencies listed specifically for Marlar in Jerauld County, South Dakota yet. Countywide channels for Jerauld County that may also cover this area are shown below when we have them. The closest trunked radio site we have is Miller (South Dakota State Radio System), about 15 miles away.

About Marlar Fire and EMS Frequencies

Quick answer: County-level fire dispatch that covers Marlar: Jerauld County Fire 151.0325 MHz, narrow FM, 131.8 PL. Trunked: South Dakota State Radio System, for example Jerauld County EMS talkgroup 1292 (hex 50c).

  • 4 conventional channels are analog FM, so any scanner can receive them. Enter the frequency and set the tone shown in the table.
  • Trunked radio systems that carry fire and EMS traffic here: South Dakota State Radio System: 1 talkgroup. A trunking scanner is required, and it must support the system type shown.
  • To follow a trunked system, program a control channel first. For Marlar, start with the Miller site of South Dakota State Radio System, about 15 miles away. Its control channels: 155.58, 159.27 MHz.

Data updated .

Jerauld County channels that also cover Marlar

Fire Dispatch

Fire Dispatch frequencies for Jerauld County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Jerauld County FireWessington Springs Fire East (with paging)151.0325
In 156.1350
131.8 PLFMNWRAL745
Jerauld County FireWessington Springs Fire West (with paging)151.0325
In 156.1350
146.2 PLFMNWRAL745

Fire Ground / Tactical

Fire Ground / Tactical frequencies for Jerauld County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Jerauld County FireAlpena Fire150.8050
In 154.2350
151.4 PLFMNWPRH257
Jerauld County FireWessington Springs Fireground151.0325146.2 PLFMNWRAL745

South Dakota State Radio System

South Dakota State Radio System talkgroups
AgencyDescriptionTalkgroupHexMode
Jerauld County EMSJerauld County EMS – Dispatch129250cD

Nearest trunked radio sites

Distances are measured from the center of Marlar.

Miller · South Dakota State Radio System
RFSS 1 · Site 10 (hex A) · NAC 47A · about 15 mi away
Control 155.58, 159.27
Voice 159.03, 159.465, 160.065
Huron · South Dakota State Radio System
RFSS 1 · Site 40 (hex 28) · about 35 mi away
Control 159.105, 159.3
Voice 156.105, 159.435
Reliance (Medicine Butte) · South Dakota State Radio System
RFSS 1 · Site 58 (hex 3A) · NAC 470 · about 38 mi away
Control 155.655, 156.03
Voice 155.85, 159.165
What do these numbers mean?
Control channel
The frequency your scanner listens to first. It tells the scanner where each voice call is happening, so program it before anything else.
Voice
The other frequencies the site uses for calls. A trunking scanner follows them automatically once it has the control channel.
Site
One tower location of the system. Scanners show the number in decimal or hex, so both are listed.
RFSS (Radio Frequency Sub-System)
A group of sites run by the same controller. Large Project 25 systems can have several.
NAC (Network Access Code)
A hex code the site transmits. Your scanner can use it to ignore other systems on the same frequency.
Talkgroup
A virtual channel on a trunked system, such as one agency’s dispatch. Programming uses the decimal or hex number, depending on your scanner.

Common questions

What frequency does the fire department use in Marlar?

We do not have a fire dispatch channel listed specifically for Marlar. The county-level fire dispatch channels in the same county: Jerauld County Fire 151.0325 MHz, narrow FM, 131.8 PL.

Do fire departments and EMS use a trunked radio system in Marlar?

Yes. The county-level systems that cover Marlar are Fire and EMS talkgroups are listed for South Dakota State Radio System: 1 talkgroup. A trunking scanner is required.

What scanner do I need to listen to fire and EMS in Marlar?

The analog conventional channels can be heard on any scanner; a trunking scanner is needed for the trunked talkgroups.

What are the control channels for trunked radio in Marlar?

For Marlar, start with the Miller site of South Dakota State Radio System. Its control channels are 155.58, 159.27 MHz. Program a control channel first; the scanner finds the voice channels from it.