About Denver Fire and EMS Frequencies
Quick answer: County-level fire dispatch that covers Denver: Kingsbury County Fire 155.5650 MHz, FM, 162.2 PL. Trunked: South Dakota State Radio System, for example Kingsbury County Fire talkgroup 1326 (hex 52e).
- 7 conventional channels are analog FM, so any scanner can receive them. Enter the frequency and set the tone shown in the table.
- Trunked radio systems that carry fire and EMS traffic here: South Dakota State Radio System: 8 talkgroups. A trunking scanner is required, and it must support the system type shown.
- To follow a trunked system, program a control channel first. For Denver, start with the Brookings site of South Dakota State Radio System, about 22 miles away. Its control channels: 157.92, 158.04 MHz.
Data updated .
Kingsbury County channels that also cover Denver
Fire Dispatch
| Agency | Description | Frequency (MHz) | Tone | Mode | FCC |
|---|---|---|---|---|---|
| Kingsbury County Fire | County Fire (2 sites) | 155.5650 In 158.9550 | 162.2 PL | FM | WPIW677 |
Fire Ground / Tactical
| Agency | Description | Frequency (MHz) | Tone | Mode | FCC |
|---|---|---|---|---|---|
| Kingsbury County Fire | Lake Preston Fire | 154.1300 In 155.5200 | FMN | KNJF649 | |
| Kingsbury County Fire | Arlington Fire | 154.2200 | FMN | WNBJ508 | |
| Kingsbury County Fire | Badger Fire | 154.9650 | FMN | WPYJ371 | |
| Kingsbury County Fire | Iroquois Fire & Rescue District | 155.7825 In 158.9175 | FMN | WPZI844 | |
| Kingsbury County Fire | De Smet Fire | 158.8650 In 153.9200 | FMN | WNZE756 |
EMS Tactical
| Agency | Description | Frequency (MHz) | Tone | Mode | FCC |
|---|---|---|---|---|---|
| Kingsbury County EMS | De Smet Ambulance | 155.4000 | FMN | WPYH225 |
South Dakota State Radio System
| Agency | Description | Talkgroup | Hex | Mode |
|---|---|---|---|---|
| Kingsbury County Fire | Kingsbury County Fire – Dispatch | 1326 | 52e | D |
| Kingsbury County Fire | Iroquis Fire / EMS | 1568 | 620 | D |
| Kingsbury County Fire | Kingsbury County Fire – Fire Ground | 1327 | 52f | D |
| Kingsbury County Fire | Kingsbury County Fire – Alternate | 1328 | 530 | D |
| Kingsbury County EMS | MED | 1319 | 527 | D |
| Kingsbury County EMS | MED | 1320 | 528 | D |
| Kingsbury County Hospital | DeSmet Hospital | 1322 | 52a | D |
| Kingsbury County Hospital | DeSmet Hospital | 1323 | 52b | D |
Nearest trunked radio sites
Distances are measured from the center of Denver.
What do these numbers mean?
- Control channel
- The frequency your scanner listens to first. It tells the scanner where each voice call is happening, so program it before anything else.
- Voice
- The other frequencies the site uses for calls. A trunking scanner follows them automatically once it has the control channel.
- Site
- One tower location of the system. Scanners show the number in decimal or hex, so both are listed.
- RFSS (Radio Frequency Sub-System)
- A group of sites run by the same controller. Large Project 25 systems can have several.
- NAC (Network Access Code)
- A hex code the site transmits. Your scanner can use it to ignore other systems on the same frequency.
- Talkgroup
- A virtual channel on a trunked system, such as one agency’s dispatch. Programming uses the decimal or hex number, depending on your scanner.
Common questions
What frequency does the fire department use in Denver?
We do not have a fire dispatch channel listed specifically for Denver. The county-level fire dispatch channels in the same county: Kingsbury County Fire 155.5650 MHz, FM, 162.2 PL.
Do fire departments and EMS use a trunked radio system in Denver?
Yes. The county-level systems that cover Denver are Fire and EMS talkgroups are listed for South Dakota State Radio System: 8 talkgroups. A trunking scanner is required.
What scanner do I need to listen to fire and EMS in Denver?
The analog conventional channels can be heard on any scanner; a trunking scanner is needed for the trunked talkgroups.
What are the control channels for trunked radio in Denver?
For Denver, start with the Brookings site of South Dakota State Radio System. Its control channels are 157.92, 158.04 MHz. Program a control channel first; the scanner finds the voice channels from it.