Skip to content

Buffalo Fire and EMS Frequencies

We do not have frequencies listed specifically for Buffalo in Marshall County, South Dakota yet. Countywide channels for Marshall County that may also cover this area are shown below when we have them. The closest trunked radio site we have is Britton (Hillhead) (South Dakota State Radio System), about 15 miles away.

About Buffalo Fire and EMS Frequencies

Quick answer: County-level fire dispatch that covers Buffalo: Marshall County Fire 155.0550 MHz, FM, 167.9 PL. Trunked: South Dakota State Radio System, for example Marshall County Fire talkgroup 1117 (hex 45d).

  • 3 conventional channels are analog FM, so any scanner can receive them. Enter the frequency and set the tone shown in the table.
  • Trunked radio systems that carry fire and EMS traffic here: South Dakota State Radio System: 2 talkgroups. A trunking scanner is required, and it must support the system type shown.
  • To follow a trunked system, program a control channel first. For Buffalo, start with the Britton (Hillhead) site of South Dakota State Radio System, about 15 miles away. Its control channels: 159.66, 159.96, 160.185 MHz.

Data updated .

Marshall County channels that also cover Buffalo

Fire Dispatch

Fire Dispatch frequencies for Marshall County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Marshall County FireLaw/CD/EMS/Fire Department Paging/Roads155.0550
In 156.0000
167.9 PLFMKAW924

EMS Tactical

EMS Tactical frequencies for Marshall County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Marshall County EMSMarshall County Hospital – EMS155.3400210.7 PLFMKBL972
Marshall County EMSMarshall County Hospital – EMS155.3850156.7 PLFMKBL972

South Dakota State Radio System

South Dakota State Radio System talkgroups
AgencyDescriptionTalkgroupHexMode
Marshall County FireMarshall County Fire – Dispatch111745dD
Marshall County EMSMarshall County EMS – Alternate1120460D

Nearest trunked radio sites

Distances are measured from the center of Buffalo.

Britton (Hillhead) · South Dakota State Radio System
RFSS 1 · Site 25 (hex 19) · NAC 479 · about 15 mi away
Control 159.66, 159.96, 160.185
Voice 157.4125
Summit · South Dakota State Radio System
RFSS 1 · Site 13 (hex D) · NAC 47D · about 19 mi away
Control 156.015, 158.64, 159.165, 160.05
Voice 157.3125, 160.515
Webster · South Dakota State Radio System
RFSS 1 · Site 16 (hex 10) · NAC 470 · about 22 mi away
Control 157.35, 158.985
Voice 156.195, 159.93
What do these numbers mean?
Control channel
The frequency your scanner listens to first. It tells the scanner where each voice call is happening, so program it before anything else.
Voice
The other frequencies the site uses for calls. A trunking scanner follows them automatically once it has the control channel.
Site
One tower location of the system. Scanners show the number in decimal or hex, so both are listed.
RFSS (Radio Frequency Sub-System)
A group of sites run by the same controller. Large Project 25 systems can have several.
NAC (Network Access Code)
A hex code the site transmits. Your scanner can use it to ignore other systems on the same frequency.
Talkgroup
A virtual channel on a trunked system, such as one agency’s dispatch. Programming uses the decimal or hex number, depending on your scanner.

Common questions

What frequency does the fire department use in Buffalo?

We do not have a fire dispatch channel listed specifically for Buffalo. The county-level fire dispatch channels in the same county: Marshall County Fire 155.0550 MHz, FM, 167.9 PL.

Do fire departments and EMS use a trunked radio system in Buffalo?

Yes. The county-level systems that cover Buffalo are Fire and EMS talkgroups are listed for South Dakota State Radio System: 2 talkgroups. A trunking scanner is required.

What scanner do I need to listen to fire and EMS in Buffalo?

The analog conventional channels can be heard on any scanner; a trunking scanner is needed for the trunked talkgroups.

What are the control channels for trunked radio in Buffalo?

For Buffalo, start with the Britton (Hillhead) site of South Dakota State Radio System. Its control channels are 159.66, 159.96, 160.185 MHz. Program a control channel first; the scanner finds the voice channels from it.