Skip to content

Newport Fire and EMS Frequencies

We do not have frequencies listed specifically for Newport in Marshall County, South Dakota yet. Countywide channels for Marshall County that may also cover this area are shown below when we have them. The closest trunked radio site we have is Webster (South Dakota State Radio System), about 27 miles away.

About Newport Fire and EMS Frequencies

Quick answer: County-level fire dispatch that covers Newport: Marshall County Fire 155.0550 MHz, FM, 167.9 PL. Trunked: South Dakota State Radio System, for example Marshall County Fire talkgroup 1117 (hex 45d).

  • 3 conventional channels are analog FM, so any scanner can receive them. Enter the frequency and set the tone shown in the table.
  • Trunked radio systems that carry fire and EMS traffic here: South Dakota State Radio System: 2 talkgroups. A trunking scanner is required, and it must support the system type shown.
  • To follow a trunked system, program a control channel first. For Newport, start with the Webster site of South Dakota State Radio System, about 27 miles away. Its control channels: 157.35, 158.985 MHz.

Data updated .

Marshall County channels that also cover Newport

Fire Dispatch

Fire Dispatch frequencies for Marshall County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Marshall County FireLaw/CD/EMS/Fire Department Paging/Roads155.0550
In 156.0000
167.9 PLFMKAW924

EMS Tactical

EMS Tactical frequencies for Marshall County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Marshall County EMSMarshall County Hospital – EMS155.3400210.7 PLFMKBL972
Marshall County EMSMarshall County Hospital – EMS155.3850156.7 PLFMKBL972

South Dakota State Radio System

South Dakota State Radio System talkgroups
AgencyDescriptionTalkgroupHexMode
Marshall County FireMarshall County Fire – Dispatch111745dD
Marshall County EMSMarshall County EMS – Alternate1120460D

Nearest trunked radio sites

Distances are measured from the center of Newport.

Webster · South Dakota State Radio System
RFSS 1 · Site 16 (hex 10) · NAC 470 · about 27 mi away
Control 157.35, 158.985
Voice 156.195, 159.93
Britton (Hillhead) · South Dakota State Radio System
RFSS 1 · Site 25 (hex 19) · NAC 479 · about 27 mi away
Control 159.66, 159.96, 160.185
Voice 157.4125
Crandall · South Dakota State Radio System
RFSS 1 · Site 21 (hex 15) · NAC 475 · about 31 mi away
Control 156.24, 159.15, 160.14
Voice 159.69
What do these numbers mean?
Control channel
The frequency your scanner listens to first. It tells the scanner where each voice call is happening, so program it before anything else.
Voice
The other frequencies the site uses for calls. A trunking scanner follows them automatically once it has the control channel.
Site
One tower location of the system. Scanners show the number in decimal or hex, so both are listed.
RFSS (Radio Frequency Sub-System)
A group of sites run by the same controller. Large Project 25 systems can have several.
NAC (Network Access Code)
A hex code the site transmits. Your scanner can use it to ignore other systems on the same frequency.
Talkgroup
A virtual channel on a trunked system, such as one agency’s dispatch. Programming uses the decimal or hex number, depending on your scanner.

Common questions

What frequency does the fire department use in Newport?

We do not have a fire dispatch channel listed specifically for Newport. The county-level fire dispatch channels in the same county: Marshall County Fire 155.0550 MHz, FM, 167.9 PL.

Do fire departments and EMS use a trunked radio system in Newport?

Yes. The county-level systems that cover Newport are Fire and EMS talkgroups are listed for South Dakota State Radio System: 2 talkgroups. A trunking scanner is required.

What scanner do I need to listen to fire and EMS in Newport?

The analog conventional channels can be heard on any scanner; a trunking scanner is needed for the trunked talkgroups.

What are the control channels for trunked radio in Newport?

For Newport, start with the Webster site of South Dakota State Radio System. Its control channels are 157.35, 158.985 MHz. Program a control channel first; the scanner finds the voice channels from it.