Skip to content

Iron Belt Fire and EMS Frequencies

We do not have frequencies listed specifically for Iron Belt in Iron County, Wisconsin yet. Countywide channels for Iron County that may also cover this area are shown below when we have them. The closest trunked radio site we have is Mercer (WISCOM), about 14 miles away.

About Iron Belt Fire and EMS Frequencies

Quick answer: County-level fire dispatch that covers Iron Belt: Iron County Fire 155.9550 MHz, narrow FM, 123.0 PL.

  • 5 conventional channels are analog FM, so any scanner can receive them. Enter the frequency and set the tone shown in the table.

Data updated .

Iron County channels that also cover Iron Belt

Fire Dispatch

Fire Dispatch frequencies for Iron County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Iron County FireIron County Fire – North (123.0 in)155.9550
In 158.9250
123.0 PLFMNWPQI677
Iron County FireIron County Fire – South (100.0 in)155.9550
In 158.9250
123.0 PLFMNWPQI677
Iron County FireIron County Fire – West (110.9 in)155.9550
In 158.9250
123.0 PLFMNWPQI677

Fire Ground / Tactical

Fire Ground / Tactical frequencies for Iron County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Iron County FireIron County Fire – Fire Ground154.0925
In 155.8425
261 DPLFMNWPQI677

Fire Talk-around

Fire Talk-around frequencies for Iron County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Iron County FireIron County Fire – Fire Ground154.1600123.0 PLFMN—

Nearest trunked radio sites

Distances are measured from the center of Iron Belt.

Mercer · WISCOM
RFSS 1 · Site 64 (hex 40) · NAC B09 · about 14 mi away
Control 139.2625, 139.6625, 151.385
Voice 154.755, 155.025
Mellen · WISCOM
RFSS 1 · Site 63 (hex 3F) · NAC B06 · about 18 mi away
Control 139.0875, 152.0375, 152.7875
Voice 151.235, 154.385
Hillside · WISCOM
RFSS 1 · Site 122 (hex 7A) · NAC B03 · about 34 mi away
Control 151.1825, 151.2275, 151.295, 151.3375
What do these numbers mean?
Control channel
The frequency your scanner listens to first. It tells the scanner where each voice call is happening, so program it before anything else.
Voice
The other frequencies the site uses for calls. A trunking scanner follows them automatically once it has the control channel.
Site
One tower location of the system. Scanners show the number in decimal or hex, so both are listed.
RFSS (Radio Frequency Sub-System)
A group of sites run by the same controller. Large Project 25 systems can have several.
NAC (Network Access Code)
A hex code the site transmits. Your scanner can use it to ignore other systems on the same frequency.
Talkgroup
A virtual channel on a trunked system, such as one agency’s dispatch. Programming uses the decimal or hex number, depending on your scanner.

Common questions

What frequency does the fire department use in Iron Belt?

We do not have a fire dispatch channel listed specifically for Iron Belt. The county-level fire dispatch channels in the same county: Iron County Fire 155.9550 MHz, narrow FM, 123.0 PL.

What scanner do I need to listen to fire and EMS in Iron Belt?

The analog conventional channels can be heard on any scanner.

What are the control channels for trunked radio in Iron Belt?

For Iron Belt, start with the Mercer site of WISCOM. Its control channels are 139.2625, 139.6625, 151.385 MHz. Program a control channel first; the scanner finds the voice channels from it.