Skip to content

Hanover Fire and EMS Frequencies

We do not have frequencies listed specifically for Hanover in Rock County, Wisconsin yet. Countywide channels for Rock County that may also cover this area are shown below when we have them. The closest trunked radio site we have is Beloit (WISCOM), about 11 miles away.

About Hanover Fire and EMS Frequencies

Quick answer: County-level fire dispatch that covers Hanover: Rock County Fire 151.2650 MHz, narrow FM, 79.7 PL. Trunked: WISCOM, for example Rock County Fire talkgroup 54407 (hex d487).

  • 4 conventional channels are analog FM, so any scanner can receive them. Enter the frequency and set the tone shown in the table.
  • 2 conventional channels use a digital mode (P25), which needs a scanner that decodes that mode.
  • Trunked radio systems that carry fire and EMS traffic here: WISCOM: 3 talkgroups. A trunking scanner is required, and it must support the system type shown.
  • To follow a trunked system, program a control channel first. For Hanover, start with the Beloit site of WISCOM, about 11 miles away. Its control channels: 138.2375, 138.5625, 139.7875 MHz.

Data updated .

Rock County channels that also cover Hanover

Fire Dispatch

Fire Dispatch frequencies for Rock County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Rock County FireCounty Paging Link151.265079.7 PLFMNKXE800
Rock County FireFire/EMS Paging154.3100
In 159.2700
79.7 PLFMNWXL609
Rock County FireFire Main155.7150
In 153.9500
NAC 540P25KXE800

Fire Talk-around

Fire Talk-around frequencies for Rock County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Rock County FireSouth155.0775
In 151.1675
127.3 PLFMNWQZT432
Rock County FireCentral155.4300
In 150.7900
NAC 540P25WQAF227
Rock County FireNorth155.6175
In 151.0475
127.3 PLFMNWQZT432

WISCOM

WISCOM talkgroups
AgencyDescriptionTalkgroupHexMode
Rock County FireTown of Beloit Fire Department54407d487D
Rock County FireTown of Milton Fire Department54462d4beD
Rock County FireTown of Rock Fire Department54482d4d2D

Nearest trunked radio sites

Distances are measured from the center of Hanover.

Beloit · WISCOM
RFSS 1 · Site 93 (hex 5D) · NAC B0C · about 11 mi away
Control 138.2375, 138.5625, 139.7875
Voice 152.1275
Milton · WISCOM
RFSS 1 · Site 10 (hex A) · NAC B01 · about 13 mi away
Control 139.2625, 139.8125
Voice 139.1125, 150.875, 152.7125, 169.675
DOC Oakhill · WISCOM
RFSS 1 · Site 210 (hex D2) · NAC B0C · about 25 mi away
Control 773.08125, 773.33125, 774.28125, 774.53125, 774.78125
What do these numbers mean?
Control channel
The frequency your scanner listens to first. It tells the scanner where each voice call is happening, so program it before anything else.
Voice
The other frequencies the site uses for calls. A trunking scanner follows them automatically once it has the control channel.
Site
One tower location of the system. Scanners show the number in decimal or hex, so both are listed.
RFSS (Radio Frequency Sub-System)
A group of sites run by the same controller. Large Project 25 systems can have several.
NAC (Network Access Code)
A hex code the site transmits. Your scanner can use it to ignore other systems on the same frequency.
Talkgroup
A virtual channel on a trunked system, such as one agency’s dispatch. Programming uses the decimal or hex number, depending on your scanner.

Common questions

What frequency does the fire department use in Hanover?

We do not have a fire dispatch channel listed specifically for Hanover. The county-level fire dispatch channels in the same county: Rock County Fire 151.2650 MHz, narrow FM, 79.7 PL.

Do fire departments and EMS use a trunked radio system in Hanover?

Yes. The county-level systems that cover Hanover are Fire and EMS talkgroups are listed for WISCOM: 3 talkgroups. A trunking scanner is required.

What scanner do I need to listen to fire and EMS in Hanover?

The analog conventional channels can be heard on any scanner; a scanner that decodes P25 is needed for the digital conventional channels; a trunking scanner is needed for the trunked talkgroups.

What are the control channels for trunked radio in Hanover?

For Hanover, start with the Beloit site of WISCOM. Its control channels are 138.2375, 138.5625, 139.7875 MHz. Program a control channel first; the scanner finds the voice channels from it.