Skip to content

Cope Fire and EMS Frequencies

We do not have frequencies listed specifically for Cope in Washington County, Colorado yet. Countywide channels for Washington County that may also cover this area are shown below when we have them. The closest trunked radio site we have is Idalia (State of Colorado DTRS), about 20 miles away.

About Cope Fire and EMS Frequencies

Quick answer: County-level fire dispatch that covers Cope: Washington County Fire 154.3850 MHz, narrow FM, no tone. Trunked: State of Colorado DTRS, for example Washington County Fire talkgroup 9048 (hex 2358).

  • 1 conventional channel is analog FM, so any scanner can receive it. Enter the frequency and set the tone shown in the table.
  • Trunked radio systems that carry fire and EMS traffic here: State of Colorado DTRS: 6 talkgroups. A trunking scanner is required, and it must support the system type shown.
  • To follow a trunked system, program a control channel first. For Cope, start with the Idalia site of State of Colorado DTRS, about 20 miles away. Its control channels: 852.075, 853.425, 853.7 MHz.

Data updated .

Washington County channels that also cover Cope

Fire Dispatch

Fire Dispatch frequencies for Washington County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Washington County FireSouthwest Washington Fire Protection District154.3850FMNWPTZ309

State of Colorado DTRS

State of Colorado DTRS talkgroups
AgencyDescriptionTalkgroupHexMode
Washington County FireCounty Fire90482358D
Washington County FireSW Washington County Fire92502422D
Washington County FireCounty Fire Tactical90452355D
Washington County FireCounty Fire Tactical90462356D
Washington County FireCounty Fire Tactical90472357D
Washington County EMSCounty EMS90492359D

Nearest trunked radio sites

Distances are measured from the center of Cope.

Idalia · State of Colorado DTRS
RFSS 3 · Site 31 (hex 1F) · NAC D1F · about 20 mi away
Control 852.075, 853.425, 853.7, 853.8875
Voice 851.9, 854.2375
Anton · State of Colorado DTRS
RFSS 3 · Site 19 (hex 13) · NAC D11 · about 22 mi away
Control 851.95, 852.7, 853.475, 853.925
Voice 851.15
Flagler · State of Colorado DTRS
RFSS 1 · Site 27 (hex 1B) · NAC D1B · about 27 mi away
Control 852.2875, 852.5625, 852.8125, 853.6
Voice 851.1125, 851.4375
What do these numbers mean?
Control channel
The frequency your scanner listens to first. It tells the scanner where each voice call is happening, so program it before anything else.
Voice
The other frequencies the site uses for calls. A trunking scanner follows them automatically once it has the control channel.
Site
One tower location of the system. Scanners show the number in decimal or hex, so both are listed.
RFSS (Radio Frequency Sub-System)
A group of sites run by the same controller. Large Project 25 systems can have several.
NAC (Network Access Code)
A hex code the site transmits. Your scanner can use it to ignore other systems on the same frequency.
Talkgroup
A virtual channel on a trunked system, such as one agency’s dispatch. Programming uses the decimal or hex number, depending on your scanner.

Common questions

What frequency does the fire department use in Cope?

We do not have a fire dispatch channel listed specifically for Cope. The county-level fire dispatch channels in the same county: Washington County Fire 154.3850 MHz, narrow FM, no tone.

Do fire departments and EMS use a trunked radio system in Cope?

Yes. The county-level systems that cover Cope are Fire and EMS talkgroups are listed for State of Colorado DTRS: 6 talkgroups. A trunking scanner is required.

What scanner do I need to listen to fire and EMS in Cope?

The analog conventional channels can be heard on any scanner; a trunking scanner is needed for the trunked talkgroups.

What are the control channels for trunked radio in Cope?

For Cope, start with the Idalia site of State of Colorado DTRS. Its control channels are 852.075, 853.425, 853.7, 853.8875 MHz. Program a control channel first; the scanner finds the voice channels from it.