About Washington Fire and EMS Frequencies
Quick answer: County-level fire dispatch that covers Washington: County Fire Dispatch 155.8350 MHz, narrow FM, 123.0 PL. Trunked: Indiana Project Hoosier SAFE-T, for example Knox County Fire talkgroup 21434 (hex 53ba).
- 6 conventional channels are analog FM, so any scanner can receive them. Enter the frequency and set the tone shown in the table.
- Trunked radio systems that carry fire and EMS traffic here: Indiana Project Hoosier SAFE-T: 10 talkgroups. A trunking scanner is required, and it must support the system type shown.
- To follow a trunked system, program a control channel first. For Washington, start with the Edwardsport site of Indiana Project Hoosier SAFE-T, about 8 miles away. Its control channels: 857.9625, 860.7625 MHz.
Data updated .
Knox County channels that also cover Washington
Fire Dispatch
| Agency | Description | Frequency (MHz) | Tone | Mode | FCC |
|---|---|---|---|---|---|
| County Fire Dispatch | County Fire Dispatch | 155.8350 In 158.8800 | 123.0 PL | FMN | KMK373 |
Fire Ground / Tactical
| Agency | Description | Frequency (MHz) | Tone | Mode | FCC |
|---|---|---|---|---|---|
| Harrison Twp Fire | Harrison Twp Fire | 154.0850 In 159.1200 | FMN | WQKZ407 | |
| Johnson Township Fire | Johnson Township Fire | 460.4000 In 465.4000 | FMN | KNEZ467 | |
| Knox County Fire | 800Mhz Backup Repeater | 854.9875 In 809.9875 | 156.7 PL | FMN | WPLQ822 |
| Palmyra Township Fire | Palmyra Township Fire | 154.3250 | FMN | KNGQ574 | |
| Vigo Township Fire | Vigo Township Fire | 154.3850 In 158.8950 | FMN | WZM743 |
Indiana Project Hoosier SAFE-T
| Agency | Description | Talkgroup | Hex | Mode |
|---|---|---|---|---|
| Knox County Fire | County Fire Multigroup | 21434 | 53ba | D |
| Knox County Fire | Fire/EMS Backup (Site Trunking Mode) | 21459 | 53d3 | D |
| Knox County Fire | Harrison Township Fire | 21442 | 53c2 | D |
| Knox County Fire | Palmyra Township Fire | 21461 | 53d5 | D |
| Knox County Fire | Steen Township Fire | 21462 | 53d6 | D |
| Knox County Fire | Vincennes Township Fire | 21465 | 53d9 | D |
| Knox County Fire | Vigo Township Fire | 21466 | 53da | D |
| Knox County Fire | Washington Township Fire | 21469 | 53dd | D |
| Knox County EMS | Good Samaritan EMS | 21445 | 53c5 | D |
| Knox County Hospital | Good Samaritan Hospital | 21446 | 53c6 | D |
Nearest trunked radio sites
Distances are measured from the center of Washington.
What do these numbers mean?
- Control channel
- The frequency your scanner listens to first. It tells the scanner where each voice call is happening, so program it before anything else.
- Voice
- The other frequencies the site uses for calls. A trunking scanner follows them automatically once it has the control channel.
- Site
- One tower location of the system. Scanners show the number in decimal or hex, so both are listed.
- RFSS (Radio Frequency Sub-System)
- A group of sites run by the same controller. Large Project 25 systems can have several.
- NAC (Network Access Code)
- A hex code the site transmits. Your scanner can use it to ignore other systems on the same frequency.
- Talkgroup
- A virtual channel on a trunked system, such as one agency’s dispatch. Programming uses the decimal or hex number, depending on your scanner.
Common questions
What frequency does the fire department use in Washington?
We do not have a fire dispatch channel listed specifically for Washington. The county-level fire dispatch channels in the same county: County Fire Dispatch 155.8350 MHz, narrow FM, 123.0 PL.
Do fire departments and EMS use a trunked radio system in Washington?
Yes. The county-level systems that cover Washington are Fire and EMS talkgroups are listed for Indiana Project Hoosier SAFE-T: 10 talkgroups. A trunking scanner is required.
What scanner do I need to listen to fire and EMS in Washington?
The analog conventional channels can be heard on any scanner; a trunking scanner is needed for the trunked talkgroups.
What are the control channels for trunked radio in Washington?
For Washington, start with the Edwardsport site of Indiana Project Hoosier SAFE-T. Its control channels are 857.9625, 860.7625 MHz. Program a control channel first; the scanner finds the voice channels from it.