Skip to content

Monroe Fire and EMS Frequencies

We do not have frequencies listed specifically for Monroe in Pike County, Indiana yet. Countywide channels for Pike County that may also cover this area are shown below when we have them. The closest trunked radio site we have is Augusta (Indiana Project Hoosier SAFE-T), about 5 miles away.

About Monroe Fire and EMS Frequencies

Quick answer: County-level fire dispatch that covers Monroe: Pike Co Fire/EMS - Dispatch 151.3700 MHz, narrow FM, 82.5 PL. Trunked: Indiana Project Hoosier SAFE-T, for example Pike County Fire talkgroup 21587 (hex 5453).

  • 5 conventional channels are analog FM, so any scanner can receive them. Enter the frequency and set the tone shown in the table.
  • 1 conventional channel uses a digital mode (NXDN48), which needs a scanner that decodes that mode.
  • Trunked radio systems that carry fire and EMS traffic here: Indiana Project Hoosier SAFE-T: 6 talkgroups. A trunking scanner is required, and it must support the system type shown.
  • To follow a trunked system, program a control channel first. For Monroe, start with the Augusta site of Indiana Project Hoosier SAFE-T, about 5 miles away. Its control channels: 853.9, 859.9875 MHz.

Data updated .

Pike County channels that also cover Monroe

Fire Dispatch

Fire Dispatch frequencies for Pike County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Pike Co Fire/EMS - DispatchPike Co Fire/EMS – Dispatch151.370082.5 PLFMNWNUK817

Fire Ground / Tactical

Fire Ground / Tactical frequencies for Pike County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Jefferson Twp Fire - OperationsJefferson Twp Fire – Operations154.340085.4 PLFMNKNBY316
Jefferson Twp Fire - OperationsJefferson Twp Fire – Operations (Digital)154.3400NXDN48KNBY316
Lockhart Twp Fire - OperationsLockhart Twp Fire – Operations154.2350118.8 PLFMNWNZZ251
Patoka Twp Fire - OperationsPatoka Twp Fire – Operations154.2500
In 158.9250
179.9 PLFMNWPMA459

EMS Tactical

EMS Tactical frequencies for Pike County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Pike Co EMS - OperationsPike Co EMS – Operations154.040082.5 PLFMNKUN492

Indiana Project Hoosier SAFE-T

Indiana Project Hoosier SAFE-T talkgroups
AgencyDescriptionTalkgroupHexMode
Pike County FirePike County Fire – Dispatch215875453D
Pike County FirePike County Fire – Fire Ground215885454D
Pike County FirePike County Fire – Fire Ground215895455D
Pike County FirePike County Fire – Fire Ground215905456D
Pike County EMSPike County EMS – Dispatch215855451D
Pike County EMSPike County EMS – Tactical Channel215865452D

Nearest trunked radio sites

Distances are measured from the center of Monroe.

Augusta · Indiana Project Hoosier SAFE-T
RFSS 2 · Site 68 (hex 44) · NAC 6B6 · about 5 mi away
Control 853.9, 859.9875
Voice 851.2625, 852.8625, 853.325
Scalesville · Indiana Project Hoosier SAFE-T
RFSS 2 · Site 26 (hex 1A) · NAC 6B2 · about 7 mi away
Control 852.4, 852.95, 853.4375
Voice 851.4
Princeton · Indiana Project Hoosier SAFE-T
RFSS 2 · Site 69 (hex 45) · NAC 6B6 · about 11 mi away
Control 853.85, 858.9875
Voice 851.0375, 853.6, 858.7125
What do these numbers mean?
Control channel
The frequency your scanner listens to first. It tells the scanner where each voice call is happening, so program it before anything else.
Voice
The other frequencies the site uses for calls. A trunking scanner follows them automatically once it has the control channel.
Site
One tower location of the system. Scanners show the number in decimal or hex, so both are listed.
RFSS (Radio Frequency Sub-System)
A group of sites run by the same controller. Large Project 25 systems can have several.
NAC (Network Access Code)
A hex code the site transmits. Your scanner can use it to ignore other systems on the same frequency.
Talkgroup
A virtual channel on a trunked system, such as one agency’s dispatch. Programming uses the decimal or hex number, depending on your scanner.

Common questions

What frequency does the fire department use in Monroe?

We do not have a fire dispatch channel listed specifically for Monroe. The county-level fire dispatch channels in the same county: Pike Co Fire/EMS - Dispatch 151.3700 MHz, narrow FM, 82.5 PL.

Do fire departments and EMS use a trunked radio system in Monroe?

Yes. The county-level systems that cover Monroe are Fire and EMS talkgroups are listed for Indiana Project Hoosier SAFE-T: 6 talkgroups. A trunking scanner is required.

What scanner do I need to listen to fire and EMS in Monroe?

The analog conventional channels can be heard on any scanner; a scanner that decodes NXDN48 is needed for the digital conventional channels; a trunking scanner is needed for the trunked talkgroups.

What are the control channels for trunked radio in Monroe?

For Monroe, start with the Augusta site of Indiana Project Hoosier SAFE-T. Its control channels are 853.9, 859.9875 MHz. Program a control channel first; the scanner finds the voice channels from it.