Skip to content

Jennings Fire and EMS Frequencies

We do not have frequencies listed specifically for Jennings in Scott County, Indiana yet. Countywide channels for Scott County that may also cover this area are shown below when we have them. The closest trunked radio site we have is Henryville (Indiana Project Hoosier SAFE-T), about 14 miles away.

About Jennings Fire and EMS Frequencies

Quick answer: County-level fire dispatch that covers Jennings: Scott County Fire 151.2125 MHz, narrow FM, 127.3 PL. Trunked: Indiana Project Hoosier SAFE-T, for example Scott County Fire talkgroup 21625 (hex 5479).

  • 2 conventional channels are analog FM, so any scanner can receive them. Enter the frequency and set the tone shown in the table.
  • 2 conventional channels use a digital mode (NXDN48, NXDN96), which needs a scanner that decodes those modes.
  • Trunked radio systems that carry fire and EMS traffic here: Indiana Project Hoosier SAFE-T: 6 talkgroups. A trunking scanner is required, and it must support the system type shown.
  • To follow a trunked system, program a control channel first. For Jennings, start with the Henryville site of Indiana Project Hoosier SAFE-T, about 14 miles away. Its control channels: 854.0375, 854.2375, 854.4125 MHz.
  • 1 listed entry is marked encrypted. No scanner can decode encrypted audio.

Data updated .

Scott County channels that also cover Jennings

Fire Dispatch

Fire Dispatch frequencies for Scott County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Scott County FireScott County Fire – Dispatch /Tone Outs151.2125
In 155.8725
127.3 PLFMNWPSH278

Fire Ground / Tactical

Fire Ground / Tactical frequencies for Scott County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Scott County FireScott County Fire – Operations151.2125
In 155.8725
RAN 14NXDN48WPSH278

EMS Dispatch

EMS Dispatch frequencies for Scott County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Scott County EMSScott County EMS – Dispatch155.1750
In 158.8725
RAN 15NXDN96 EncryptedWPSH278

EMS Tactical

EMS Tactical frequencies for Scott County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Scott County EMSScott County EMS – Tactical Channel153.8000CSQFMNWPSH278

Indiana Project Hoosier SAFE-T

Indiana Project Hoosier SAFE-T talkgroups
AgencyDescriptionTalkgroupHexMode
Scott County FireScott County Fire – Dispatch216255479D
Scott County FireScott County Fire – Fire Ground21626547aD
Scott County FireScott County Fire – Fire Ground21627547bD
Scott County FireScott County Fire – Fire Ground21628547cD
Scott County EMSScott County EMS – Operations216225476D
Scott County HospitalScott County Hospital – Operations (IHERN)216235477D

Nearest trunked radio sites

Distances are measured from the center of Jennings.

Henryville · Indiana Project Hoosier SAFE-T
RFSS 2 · Site 33 (hex 21) · NAC 6B3 · about 14 mi away
Control 854.0375, 854.2375, 854.4125, 857.7125
Voice 851.425, 851.925, 852.925, 853.425, 853.925
Fleenortown · Indiana Project Hoosier SAFE-T
RFSS 2 · Site 50 (hex 32) · NAC 6B8 · about 14 mi away
Control 853.4625, 855.7125
Voice 851.3125, 851.725, 852.95
Seymour · Indiana Project Hoosier SAFE-T
RFSS 2 · Site 32 (hex 20) · NAC 6B9 · about 15 mi away
Control 853.9125
Voice 851.4625, 852.4125, 852.8875, 853.3625, 856.7125
What do these numbers mean?
Control channel
The frequency your scanner listens to first. It tells the scanner where each voice call is happening, so program it before anything else.
Voice
The other frequencies the site uses for calls. A trunking scanner follows them automatically once it has the control channel.
Site
One tower location of the system. Scanners show the number in decimal or hex, so both are listed.
RFSS (Radio Frequency Sub-System)
A group of sites run by the same controller. Large Project 25 systems can have several.
NAC (Network Access Code)
A hex code the site transmits. Your scanner can use it to ignore other systems on the same frequency.
Talkgroup
A virtual channel on a trunked system, such as one agency’s dispatch. Programming uses the decimal or hex number, depending on your scanner.

Common questions

What frequency does the fire department use in Jennings?

We do not have a fire dispatch channel listed specifically for Jennings. The county-level fire dispatch channels in the same county: Scott County Fire 151.2125 MHz, narrow FM, 127.3 PL.

Do fire departments and EMS use a trunked radio system in Jennings?

Yes. The county-level systems that cover Jennings are Fire and EMS talkgroups are listed for Indiana Project Hoosier SAFE-T: 6 talkgroups. A trunking scanner is required.

What scanner do I need to listen to fire and EMS in Jennings?

The analog conventional channels can be heard on any scanner; a scanner that decodes NXDN48, NXDN96 is needed for the digital conventional channels; a trunking scanner is needed for the trunked talkgroups.

What are the control channels for trunked radio in Jennings?

For Jennings, start with the Henryville site of Indiana Project Hoosier SAFE-T. Its control channels are 854.0375, 854.2375, 854.4125, 857.7125 MHz. Program a control channel first; the scanner finds the voice channels from it.