Skip to content

Harmony Fire and EMS Frequencies

We do not have frequencies listed specifically for Harmony in Union County, Indiana yet. Countywide channels for Union County that may also cover this area are shown below when we have them. The closest trunked radio site we have is Brookville (Indiana Project Hoosier SAFE-T), about 6 miles away.

About Harmony Fire and EMS Frequencies

Quick answer: County-level ems dispatch that covers Harmony: Union County EMS 155.1600 MHz, narrow FM, 465 DPL. Trunked: Indiana Project Hoosier SAFE-T, for example Union County Fire talkgroup 12354 (hex 3042).

  • 1 conventional channel is analog FM, so any scanner can receive it. Enter the frequency and set the tone shown in the table.
  • Trunked radio systems that carry fire and EMS traffic here: Indiana Project Hoosier SAFE-T: 7 talkgroups. A trunking scanner is required, and it must support the system type shown.
  • To follow a trunked system, program a control channel first. For Harmony, start with the Brookville site of Indiana Project Hoosier SAFE-T, about 6 miles away. Its control channels: 853.8875 MHz.

Data updated .

Union County channels that also cover Harmony

EMS Dispatch

EMS Dispatch frequencies for Union County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Union County EMSUnion County EMS – Dispatch155.1600465 DPLFMN—

Indiana Project Hoosier SAFE-T

Indiana Project Hoosier SAFE-T talkgroups
AgencyDescriptionTalkgroupHexMode
Union County FireUnion County Fire – Dispatch (County)123543042D
Union County FireUnion County Fire – Fire Ground (County)123553043D
Union County FireUnion County Fire – Fire Ground (County)123563044D
Union County FireUnion County Fire – Fire Ground (County)123573045D
Union County EMSUnion County EMS – Dispatch (County)12351303fD
Union County EMSUnion County EMS – Operations (County)123523040D
Union County EMSUnion County EMS – Operations (County)123533041D

Nearest trunked radio sites

Distances are measured from the center of Harmony.

Brookville · Indiana Project Hoosier SAFE-T
RFSS 2 · Site 41 (hex 29) · NAC 6B4 · about 6 mi away
Control 853.8875
Voice 851.475, 851.975, 853.475, 853.7
Connersville · Indiana Project Hoosier SAFE-T
RFSS 1 · Site 38 (hex 26) · NAC 6B8 · about 11 mi away
Control 851.8875, 852.3875, 853.725
Voice 851.2, 851.45
Peppertown · Indiana Project Hoosier SAFE-T
RFSS 2 · Site 28 (hex 1C) · NAC 6B2 · about 15 mi away
Control 857.7125, 858.7125
Voice 851.8625, 852.3625, 852.875
What do these numbers mean?
Control channel
The frequency your scanner listens to first. It tells the scanner where each voice call is happening, so program it before anything else.
Voice
The other frequencies the site uses for calls. A trunking scanner follows them automatically once it has the control channel.
Site
One tower location of the system. Scanners show the number in decimal or hex, so both are listed.
RFSS (Radio Frequency Sub-System)
A group of sites run by the same controller. Large Project 25 systems can have several.
NAC (Network Access Code)
A hex code the site transmits. Your scanner can use it to ignore other systems on the same frequency.
Talkgroup
A virtual channel on a trunked system, such as one agency’s dispatch. Programming uses the decimal or hex number, depending on your scanner.

Common questions

What frequency does EMS or the ambulance service use in Harmony?

We do not have a EMS dispatch channel listed specifically for Harmony. The county-level EMS dispatch channels in the same county: Union County EMS 155.1600 MHz, narrow FM, 465 DPL.

Do fire departments and EMS use a trunked radio system in Harmony?

Yes. The county-level systems that cover Harmony are Fire and EMS talkgroups are listed for Indiana Project Hoosier SAFE-T: 7 talkgroups. A trunking scanner is required.

What scanner do I need to listen to fire and EMS in Harmony?

The analog conventional channels can be heard on any scanner; a trunking scanner is needed for the trunked talkgroups.

What are the control channels for trunked radio in Harmony?

For Harmony, start with the Brookville site of Indiana Project Hoosier SAFE-T. Its control channels are 853.8875 MHz. Program a control channel first; the scanner finds the voice channels from it.