Skip to content

Pierce Fire and EMS Frequencies

We do not have frequencies listed specifically for Pierce in Washington County, Indiana yet. Countywide channels for Washington County that may also cover this area are shown below when we have them. The closest trunked radio site we have is Pekin (Indiana Project Hoosier SAFE-T), about 6 miles away.

About Pierce Fire and EMS Frequencies

Quick answer: County-level fire dispatch that covers Pierce: Washington County Fire 155.4900 MHz, narrow FM, 167.9 PL. County-level ems dispatch that covers Pierce: Washington County EMS 155.9025 MHz, NXDN48, RAN 22. Trunked: Indiana Project Hoosier SAFE-T, for example Washington County Fire talkgroup 21694 (hex 54be).

  • 5 conventional channels are analog FM, so any scanner can receive them. Enter the frequency and set the tone shown in the table.
  • 1 conventional channel uses a digital mode (NXDN48), which needs a scanner that decodes that mode.
  • Trunked radio systems that carry fire and EMS traffic here: Indiana Project Hoosier SAFE-T: 6 talkgroups. A trunking scanner is required, and it must support the system type shown.
  • To follow a trunked system, program a control channel first. For Pierce, start with the Pekin site of Indiana Project Hoosier SAFE-T, about 6 miles away. Its control channels: 853.85 MHz.

Data updated .

Washington County channels that also cover Pierce

Fire Dispatch

Fire Dispatch frequencies for Washington County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Washington County FireWashington County Fire – Repeater155.4900
In 153.9950
167.9 PLFMNWQF450

Fire Ground / Tactical

Fire Ground / Tactical frequencies for Washington County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Washington County FireWashington County Fire – Posey Twp151.2725
In 159.3225
FMNWQFB901
Washington County FireWashington County Fire – Tactical Channel153.9950FMNWQF450
Washington County FireWashington County Fire – Tactical Channel154.1900167.9 PLFMNWQF450
Washington County FireEmergency Management Agency155.9400FMNWNKG271

EMS Dispatch

EMS Dispatch frequencies for Washington County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Washington County EMSWashington County EMS – Dispatch155.9025RAN 22NXDN48WQF450

Indiana Project Hoosier SAFE-T

Indiana Project Hoosier SAFE-T talkgroups
AgencyDescriptionTalkgroupHexMode
Washington County FireWashington County Fire – Dispatch (County)2169454beD
Washington County FireWashington County Fire – Operations (County)2169554bfD
Washington County FireWashington County Fire – Tactical Channel (County)2169654c0D
Washington County EMSWashington County EMS – Dispatch (County)2169154bbD
Washington County EMSWashington County EMS – Operations (County)2169254bcD
Washington County EMSWashington County EMS – Tactical Channel (County)2169354bdD

Nearest trunked radio sites

Distances are measured from the center of Pierce.

Pekin · Indiana Project Hoosier SAFE-T
RFSS 2 · Site 52 (hex 34) · NAC 6B5 · about 6 mi away
Control 853.85
Voice 852.7875, 853.2125, 853.8125, 853.975
Fleenortown · Indiana Project Hoosier SAFE-T
RFSS 2 · Site 50 (hex 32) · NAC 6B8 · about 10 mi away
Control 853.4625, 855.7125
Voice 851.3125, 851.725, 852.95
Salem · Indiana Project Hoosier SAFE-T
RFSS 2 · Site 51 (hex 33) · NAC 6B5 · about 10 mi away
Control 853.975
Voice 852.7875, 853.2125, 853.8125
What do these numbers mean?
Control channel
The frequency your scanner listens to first. It tells the scanner where each voice call is happening, so program it before anything else.
Voice
The other frequencies the site uses for calls. A trunking scanner follows them automatically once it has the control channel.
Site
One tower location of the system. Scanners show the number in decimal or hex, so both are listed.
RFSS (Radio Frequency Sub-System)
A group of sites run by the same controller. Large Project 25 systems can have several.
NAC (Network Access Code)
A hex code the site transmits. Your scanner can use it to ignore other systems on the same frequency.
Talkgroup
A virtual channel on a trunked system, such as one agency’s dispatch. Programming uses the decimal or hex number, depending on your scanner.

Common questions

What frequency does the fire department use in Pierce?

We do not have a fire dispatch channel listed specifically for Pierce. The county-level fire dispatch channels in the same county: Washington County Fire 155.4900 MHz, narrow FM, 167.9 PL.

What frequency does EMS or the ambulance service use in Pierce?

We do not have a EMS dispatch channel listed specifically for Pierce. The county-level EMS dispatch channels in the same county: Washington County EMS 155.9025 MHz, NXDN48, RAN 22.

Do fire departments and EMS use a trunked radio system in Pierce?

Yes. The county-level systems that cover Pierce are Fire and EMS talkgroups are listed for Indiana Project Hoosier SAFE-T: 6 talkgroups. A trunking scanner is required.

What scanner do I need to listen to fire and EMS in Pierce?

The analog conventional channels can be heard on any scanner; a scanner that decodes NXDN48 is needed for the digital conventional channels; a trunking scanner is needed for the trunked talkgroups.

What are the control channels for trunked radio in Pierce?

For Pierce, start with the Pekin site of Indiana Project Hoosier SAFE-T. Its control channels are 853.85 MHz. Program a control channel first; the scanner finds the voice channels from it.