Skip to content

Elm Fire and EMS Frequencies

We do not have frequencies listed specifically for Elm in Allen County, Kansas yet. Countywide channels for Allen County that may also cover this area are shown below when we have them. The closest trunked radio site we have is Xenia (Kansas Statewide Interoperable Communication System (KSICS)), about 16 miles away.

About Elm Fire and EMS Frequencies

Quick answer: County-level fire dispatch that covers Elm: Allen County Fire 460.6000 MHz, narrow FM, 91.5 PL. County-level ems dispatch that covers Elm: Allen County EMS 463.1750 MHz, narrow FM, 192.8 PL.

  • 2 conventional channels are analog FM, so any scanner can receive them. Enter the frequency and set the tone shown in the table.

Data updated .

Allen County channels that also cover Elm

Fire Dispatch

Fire Dispatch frequencies for Allen County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Allen County FireAllen County Fire – Dispatch460.6000
In 465.6000
91.5 PLFMNWPIT496

EMS Dispatch

EMS Dispatch frequencies for Allen County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Allen County EMSAllen County EMS – Dispatch463.1750
In 468.1750
192.8 PLFMNWNAH460

Nearest trunked radio sites

Distances are measured from the center of Elm.

Xenia · Kansas Statewide Interoperable Communication System (KSICS)
RFSS 1 · Site 10 (hex A) · NAC 1BB · about 16 mi away
Control 851.625, 852.2
Voice 851.375, 852.55, 853.175, 853.3, 853.675
Buffalo · Kansas Statewide Interoperable Communication System (KSICS)
RFSS 1 · Site 3 (hex 3) · NAC 1B0 · about 22 mi away
Control 852.4625, 852.725
Voice 851.8375, 852.975, 853.4, 853.8625
Garnett · Kansas Statewide Interoperable Communication System (KSICS)
RFSS 1 · Site 66 (hex 42) · NAC 1B0 · about 23 mi away
Control 854.4125, 854.6625
Voice 854.1625, 856.4375, 857.0375, 857.4625
What do these numbers mean?
Control channel
The frequency your scanner listens to first. It tells the scanner where each voice call is happening, so program it before anything else.
Voice
The other frequencies the site uses for calls. A trunking scanner follows them automatically once it has the control channel.
Site
One tower location of the system. Scanners show the number in decimal or hex, so both are listed.
RFSS (Radio Frequency Sub-System)
A group of sites run by the same controller. Large Project 25 systems can have several.
NAC (Network Access Code)
A hex code the site transmits. Your scanner can use it to ignore other systems on the same frequency.
Talkgroup
A virtual channel on a trunked system, such as one agency’s dispatch. Programming uses the decimal or hex number, depending on your scanner.

Common questions

What frequency does the fire department use in Elm?

We do not have a fire dispatch channel listed specifically for Elm. The county-level fire dispatch channels in the same county: Allen County Fire 460.6000 MHz, narrow FM, 91.5 PL.

What frequency does EMS or the ambulance service use in Elm?

We do not have a EMS dispatch channel listed specifically for Elm. The county-level EMS dispatch channels in the same county: Allen County EMS 463.1750 MHz, narrow FM, 192.8 PL.

What scanner do I need to listen to fire and EMS in Elm?

The analog conventional channels can be heard on any scanner.

What are the control channels for trunked radio in Elm?

For Elm, start with the Xenia site of Kansas Statewide Interoperable Communication System (KSICS). Its control channels are 851.625, 852.2 MHz. Program a control channel first; the scanner finds the voice channels from it.