Skip to content

Cheyenne Fire and EMS Frequencies

We do not have frequencies listed specifically for Cheyenne in Lane County, Kansas yet. Countywide channels for Lane County that may also cover this area are shown below when we have them. The closest trunked radio site we have is Dighton (Kansas Statewide Interoperable Communication System (KSICS)), about 19 miles away.

About Cheyenne Fire and EMS Frequencies

Quick answer: County-level fire dispatch that covers Cheyenne: Lane County Fire 154.1450 MHz, narrow FM, no tone. Trunked: Kansas Statewide Interoperable Communication System (KSICS), for example Lane County Hospital talkgroup 2441 (hex 989).

  • 1 conventional channel is analog FM, so any scanner can receive it. Enter the frequency and set the tone shown in the table.
  • Trunked radio systems that carry fire and EMS traffic here: Kansas Statewide Interoperable Communication System (KSICS): 1 talkgroup. A trunking scanner is required, and it must support the system type shown.
  • To follow a trunked system, program a control channel first. For Cheyenne, start with the Dighton site of Kansas Statewide Interoperable Communication System (KSICS), about 19 miles away. Its control channels: 852.1125, 852.4125 MHz.

Data updated .

Lane County channels that also cover Cheyenne

Fire Dispatch

Fire Dispatch frequencies for Lane County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Lane County FireLane County Fire – Dispatch154.1450
In 158.8650
FMNWQCI323

Kansas Statewide Interoperable Communication System (KSICS)

Kansas Statewide Interoperable Communication System (KSICS) talkgroups
AgencyDescriptionTalkgroupHexMode
Lane County HospitalHospital ER – Patient Reports2441989D

Nearest trunked radio sites

Distances are measured from the center of Cheyenne.

Dighton · Kansas Statewide Interoperable Communication System (KSICS)
RFSS 1 · Site 29 (hex 1D) · NAC 1B1 · about 19 mi away
Control 852.1125, 852.4125
Voice 851.8, 852.75, 853.475, 853.9
Quinter · Kansas Statewide Interoperable Communication System (KSICS)
RFSS 2 · Site 31 (hex 1F) · NAC 1B5 · about 26 mi away
Control 851.55, 852.3375
Voice 851.275, 852.175, 853.175, 853.35, 853.6125
Oakley · Kansas Statewide Interoperable Communication System (KSICS)
RFSS 2 · Site 42 (hex 2A) · NAC 1B6 · about 27 mi away
Control 852.4875, 852.775
Voice 851.7125, 853.075, 853.425, 853.725
What do these numbers mean?
Control channel
The frequency your scanner listens to first. It tells the scanner where each voice call is happening, so program it before anything else.
Voice
The other frequencies the site uses for calls. A trunking scanner follows them automatically once it has the control channel.
Site
One tower location of the system. Scanners show the number in decimal or hex, so both are listed.
RFSS (Radio Frequency Sub-System)
A group of sites run by the same controller. Large Project 25 systems can have several.
NAC (Network Access Code)
A hex code the site transmits. Your scanner can use it to ignore other systems on the same frequency.
Talkgroup
A virtual channel on a trunked system, such as one agency’s dispatch. Programming uses the decimal or hex number, depending on your scanner.

Common questions

What frequency does the fire department use in Cheyenne?

We do not have a fire dispatch channel listed specifically for Cheyenne. The county-level fire dispatch channels in the same county: Lane County Fire 154.1450 MHz, narrow FM, no tone.

Do fire departments and EMS use a trunked radio system in Cheyenne?

Yes. The county-level systems that cover Cheyenne are Fire and EMS talkgroups are listed for Kansas Statewide Interoperable Communication System (KSICS): 1 talkgroup. A trunking scanner is required.

What scanner do I need to listen to fire and EMS in Cheyenne?

The analog conventional channels can be heard on any scanner; a trunking scanner is needed for the trunked talkgroups.

What are the control channels for trunked radio in Cheyenne?

For Cheyenne, start with the Dighton site of Kansas Statewide Interoperable Communication System (KSICS). Its control channels are 852.1125, 852.4125 MHz. Program a control channel first; the scanner finds the voice channels from it.