Skip to content

Barrett Fire and EMS Frequencies

We do not have frequencies listed specifically for Barrett in Thomas County, Kansas yet. Countywide channels for Thomas County that may also cover this area are shown below when we have them. The closest trunked radio site we have is Colby (Kansas Statewide Interoperable Communication System (KSICS)), about 15 miles away.

About Barrett Fire and EMS Frequencies

Quick answer: County-level ems dispatch that covers Barrett: Thomas County EMS 462.9500 MHz, narrow FM, 192.8 PL. Trunked: Kansas Statewide Interoperable Communication System (KSICS), for example Thomas County EMS talkgroup 4461 (hex 116d).

  • 1 conventional channel is analog FM, so any scanner can receive it. Enter the frequency and set the tone shown in the table.
  • Trunked radio systems that carry fire and EMS traffic here: Kansas Statewide Interoperable Communication System (KSICS): 1 talkgroup. A trunking scanner is required, and it must support the system type shown.
  • To follow a trunked system, program a control channel first. For Barrett, start with the Colby site of Kansas Statewide Interoperable Communication System (KSICS), about 15 miles away. Its control channels: 857.4625, 857.9625 MHz.

Data updated .

Thomas County channels that also cover Barrett

EMS Dispatch

EMS Dispatch frequencies for Thomas County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Thomas County EMSThomas County EMS – Dispatch (before KSICS)462.9500
In 467.9500
192.8 PLFMNKNBJ887

Kansas Statewide Interoperable Communication System (KSICS)

Kansas Statewide Interoperable Communication System (KSICS) talkgroups
AgencyDescriptionTalkgroupHexMode
Thomas County EMSCounty EMS Dispatch4461116dD

Nearest trunked radio sites

Distances are measured from the center of Barrett.

Colby · Kansas Statewide Interoperable Communication System (KSICS)
RFSS 2 · Site 59 (hex 3B) · NAC 1B1 · about 15 mi away
Control 857.4625, 857.9625
Voice 856.4625, 858.4625, 859.4625, 859.9375
McDonald · Kansas Statewide Interoperable Communication System (KSICS)
RFSS 2 · Site 35 (hex 23) · NAC 1B5 · about 19 mi away
Control 852.4625, 852.725
Voice 851.8375, 852.975, 853.4, 853.8625
Edson · Kansas Statewide Interoperable Communication System (KSICS)
RFSS 2 · Site 39 (hex 27) · NAC 1B4 · about 19 mi away
Control 852.1125, 852.4125
Voice 851.8, 852.75, 853.475, 853.9
What do these numbers mean?
Control channel
The frequency your scanner listens to first. It tells the scanner where each voice call is happening, so program it before anything else.
Voice
The other frequencies the site uses for calls. A trunking scanner follows them automatically once it has the control channel.
Site
One tower location of the system. Scanners show the number in decimal or hex, so both are listed.
RFSS (Radio Frequency Sub-System)
A group of sites run by the same controller. Large Project 25 systems can have several.
NAC (Network Access Code)
A hex code the site transmits. Your scanner can use it to ignore other systems on the same frequency.
Talkgroup
A virtual channel on a trunked system, such as one agency’s dispatch. Programming uses the decimal or hex number, depending on your scanner.

Common questions

What frequency does EMS or the ambulance service use in Barrett?

We do not have a EMS dispatch channel listed specifically for Barrett. The county-level EMS dispatch channels in the same county: Thomas County EMS 462.9500 MHz, narrow FM, 192.8 PL.

Do fire departments and EMS use a trunked radio system in Barrett?

Yes. The county-level systems that cover Barrett are Fire and EMS talkgroups are listed for Kansas Statewide Interoperable Communication System (KSICS): 1 talkgroup. A trunking scanner is required.

What scanner do I need to listen to fire and EMS in Barrett?

The analog conventional channels can be heard on any scanner; a trunking scanner is needed for the trunked talkgroups.

What are the control channels for trunked radio in Barrett?

For Barrett, start with the Colby site of Kansas Statewide Interoperable Communication System (KSICS). Its control channels are 857.4625, 857.9625 MHz. Program a control channel first; the scanner finds the voice channels from it.