Skip to content

Glencoe Fire and EMS Frequencies

We do not have frequencies listed specifically for Glencoe in Trego County, Kansas yet. Countywide channels for Trego County that may also cover this area are shown below when we have them. The closest trunked radio site we have is Ellis (Kansas Statewide Interoperable Communication System (KSICS)), about 5 miles away.

About Glencoe Fire and EMS Frequencies

Quick answer: County-level fire dispatch that covers Glencoe: Trego County Fire 158.8350 MHz, narrow FM, 141.3 PL. Trunked: Kansas Statewide Interoperable Communication System (KSICS), for example Trego County Fire talkgroup 4355 (hex 1103).

  • 1 conventional channel is analog FM, so any scanner can receive it. Enter the frequency and set the tone shown in the table.
  • Trunked radio systems that carry fire and EMS traffic here: Kansas Statewide Interoperable Communication System (KSICS): 4 talkgroups. A trunking scanner is required, and it must support the system type shown.
  • To follow a trunked system, program a control channel first. For Glencoe, start with the Ellis site of Kansas Statewide Interoperable Communication System (KSICS), about 5 miles away. Its control channels: 852.3125, 852.6125 MHz.

Data updated .

Trego County channels that also cover Glencoe

Fire Dispatch

Fire Dispatch frequencies for Trego County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Trego County FireTrego County Fire – Dispatch (Dispatch before KSICS)158.8350
In 153.7400
141.3 PLFMNWPWT921

Kansas Statewide Interoperable Communication System (KSICS)

Kansas Statewide Interoperable Communication System (KSICS) talkgroups
AgencyDescriptionTalkgroupHexMode
Trego County FireTrego County Fire – Dispatch43551103D
Trego County FireTrego County Fire – Tactical Channel43561104D
Trego County FireTrego County Fire – Tactical Channel43571105D
Trego County EMSTrego County EMS – Tactical Channel43541102D

Nearest trunked radio sites

Distances are measured from the center of Glencoe.

Ellis · Kansas Statewide Interoperable Communication System (KSICS)
RFSS 2 · Site 30 (hex 1E) · NAC 1BC · about 5 mi away
Control 852.3125, 852.6125
Voice 851.6, 852.9375, 853.1875, 853.65
Site 1 · Ellis County
RFSS 1 · Site 1 (hex 1) · NAC 971 · about 17 mi away
Control 856.7625, 857.2125, 857.7625
Voice 856.2125, 858.2125, 858.7625, 859.2125, 859.7625
Hays · Kansas Statewide Interoperable Communication System (KSICS)
RFSS 2 · Site 45 (hex 2D) · NAC 1BF · about 18 mi away
Control 851.975, 852.3625
Voice 851.225, 852.55, 852.875, 853.225, 853.55, 853.825
What do these numbers mean?
Control channel
The frequency your scanner listens to first. It tells the scanner where each voice call is happening, so program it before anything else.
Voice
The other frequencies the site uses for calls. A trunking scanner follows them automatically once it has the control channel.
Site
One tower location of the system. Scanners show the number in decimal or hex, so both are listed.
RFSS (Radio Frequency Sub-System)
A group of sites run by the same controller. Large Project 25 systems can have several.
NAC (Network Access Code)
A hex code the site transmits. Your scanner can use it to ignore other systems on the same frequency.
Talkgroup
A virtual channel on a trunked system, such as one agency’s dispatch. Programming uses the decimal or hex number, depending on your scanner.

Common questions

What frequency does the fire department use in Glencoe?

We do not have a fire dispatch channel listed specifically for Glencoe. The county-level fire dispatch channels in the same county: Trego County Fire 158.8350 MHz, narrow FM, 141.3 PL.

Do fire departments and EMS use a trunked radio system in Glencoe?

Yes. The county-level systems that cover Glencoe are Fire and EMS talkgroups are listed for Kansas Statewide Interoperable Communication System (KSICS): 4 talkgroups. A trunking scanner is required.

What scanner do I need to listen to fire and EMS in Glencoe?

The analog conventional channels can be heard on any scanner; a trunking scanner is needed for the trunked talkgroups.

What are the control channels for trunked radio in Glencoe?

For Glencoe, start with the Ellis site of Kansas Statewide Interoperable Communication System (KSICS). Its control channels are 852.3125, 852.6125 MHz. Program a control channel first; the scanner finds the voice channels from it.