Skip to content

Millward Fire and EMS Frequencies

We do not have frequencies listed specifically for Millward in Aitkin County, Minnesota yet. Countywide channels for Aitkin County that may also cover this area are shown below when we have them. The closest trunked radio site we have is McGrath (Allied Radio Matrix for Emergency Response (ARMER)), about 7 miles away.

About Millward Fire and EMS Frequencies

Quick answer: County-level fire dispatch that covers Millward: Aitkin County Fire 154.4450 MHz, narrow FM, 141.3 PL. Trunked: Allied Radio Matrix for Emergency Response (ARMER), for example Aitkin County Fire talkgroup 36919 (hex 9037).

  • 2 conventional channels are analog FM, so any scanner can receive them. Enter the frequency and set the tone shown in the table.
  • Trunked radio systems that carry fire and EMS traffic here: Allied Radio Matrix for Emergency Response (ARMER): 2 talkgroups. A trunking scanner is required, and it must support the system type shown.
  • To follow a trunked system, program a control channel first. For Millward, start with the McGrath site of Allied Radio Matrix for Emergency Response (ARMER), about 7 miles away. Its control channels: 856.4875, 857.9625 MHz.

Data updated .

Aitkin County channels that also cover Millward

Fire Dispatch

Fire Dispatch frequencies for Aitkin County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Aitkin County FireCounty Fire / Rescue Paging154.4450141.3 PLFMNWQF590

Hospitals & Medical

Hospitals & Medical frequencies for Aitkin County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Aitkin County HospitalRiverwood Health Care Center155.3550167.9 PLFMNWQCA908

Allied Radio Matrix for Emergency Response (ARMER)

Allied Radio Matrix for Emergency Response (ARMER) talkgroups
AgencyDescriptionTalkgroupHexMode
Aitkin County FireAitkin City Fire Tactical369199037D
Aitkin County HospitalRiverwood Hospital ER Aitkin36925903dD

Nearest trunked radio sites

Distances are measured from the center of Millward.

McGrath · Allied Radio Matrix for Emergency Response (ARMER)
RFSS 5 · Site 10 (hex A) · NAC 405 · about 7 mi away
Control 856.4875, 857.9625
Voice 851.9125, 852.4125, 854.9875
Lawler · Allied Radio Matrix for Emergency Response (ARMER)
RFSS 5 · Site 8 (hex 8) · NAC 406 · about 16 mi away
Control 853.9125, 855.2375
Voice 851.9375, 852.8875, 853.3875
Moose Lake Lookout · Allied Radio Matrix for Emergency Response (ARMER)
RFSS 5 · Site 19 (hex 13) · NAC 401 · about 16 mi away
Control 852.2, 858.9375, 859.2125
Voice 851.3875, 852.3875, 854.1875, 854.6375, 856.9375, 859.9375
What do these numbers mean?
Control channel
The frequency your scanner listens to first. It tells the scanner where each voice call is happening, so program it before anything else.
Voice
The other frequencies the site uses for calls. A trunking scanner follows them automatically once it has the control channel.
Site
One tower location of the system. Scanners show the number in decimal or hex, so both are listed.
RFSS (Radio Frequency Sub-System)
A group of sites run by the same controller. Large Project 25 systems can have several.
NAC (Network Access Code)
A hex code the site transmits. Your scanner can use it to ignore other systems on the same frequency.
Talkgroup
A virtual channel on a trunked system, such as one agency’s dispatch. Programming uses the decimal or hex number, depending on your scanner.

Common questions

What frequency does the fire department use in Millward?

We do not have a fire dispatch channel listed specifically for Millward. The county-level fire dispatch channels in the same county: Aitkin County Fire 154.4450 MHz, narrow FM, 141.3 PL.

Do fire departments and EMS use a trunked radio system in Millward?

Yes. The county-level systems that cover Millward are Fire and EMS talkgroups are listed for Allied Radio Matrix for Emergency Response (ARMER): 2 talkgroups. A trunking scanner is required.

What scanner do I need to listen to fire and EMS in Millward?

The analog conventional channels can be heard on any scanner; a trunking scanner is needed for the trunked talkgroups.

What are the control channels for trunked radio in Millward?

For Millward, start with the McGrath site of Allied Radio Matrix for Emergency Response (ARMER). Its control channels are 856.4875, 857.9625 MHz. Program a control channel first; the scanner finds the voice channels from it.