Skip to content

Wilmington Fire and EMS Frequencies

We do not have frequencies listed specifically for Wilmington in Houston County, Minnesota yet. Countywide channels for Houston County that may also cover this area are shown below when we have them. The closest trunked radio site we have is Spring Grove (Allied Radio Matrix for Emergency Response (ARMER)), about 4 miles away.

About Wilmington Fire and EMS Frequencies

Quick answer: County-level fire dispatch that covers Wilmington: Houston County Fire 154.3550 MHz, narrow FM, 192.8 PL. Trunked: Allied Radio Matrix for Emergency Response (ARMER), for example Houston County Fire talkgroup 22023 (hex 5607).

  • 1 conventional channel is analog FM, so any scanner can receive it. Enter the frequency and set the tone shown in the table.
  • Trunked radio systems that carry fire and EMS traffic here: Allied Radio Matrix for Emergency Response (ARMER): 3 talkgroups. A trunking scanner is required, and it must support the system type shown.
  • To follow a trunked system, program a control channel first. For Wilmington, start with the Spring Grove site of Allied Radio Matrix for Emergency Response (ARMER), about 4 miles away. Its control channels: 852.15 MHz.

Data updated .

Houston County channels that also cover Wilmington

Fire Dispatch

Fire Dispatch frequencies for Houston County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Houston County FireCounty Fire154.3550
In 153.7700
192.8 PLFMNKUT918

Allied Radio Matrix for Emergency Response (ARMER)

Allied Radio Matrix for Emergency Response (ARMER) talkgroups
AgencyDescriptionTalkgroupHexMode
Houston County FireCounty Fire Dispatch220235607D
Houston County FireCounty Fire220245608D
Houston County FireCounty Fire220255609D

Nearest trunked radio sites

Distances are measured from the center of Wilmington.

Spring Grove · Allied Radio Matrix for Emergency Response (ARMER)
RFSS 3 · Site 24 (hex 18) · NAC 40d · about 4 mi away
Control 852.15
Voice 851.725, 852.4375, 853.1, 853.4375
Reno · Allied Radio Matrix for Emergency Response (ARMER)
RFSS 3 · Site 23 (hex 17) · NAC 40C · about 10 mi away
Control 857.7125
Voice 852.65, 854.9875, 855.2375, 855.7125
Caledonia · Allied Radio Matrix for Emergency Response (ARMER)
RFSS 3 · Site 3 (hex 3) · NAC 40B · about 12 mi away
Control 858.4375
Voice 852.125, 857.9375, 858.7625, 859.2375
What do these numbers mean?
Control channel
The frequency your scanner listens to first. It tells the scanner where each voice call is happening, so program it before anything else.
Voice
The other frequencies the site uses for calls. A trunking scanner follows them automatically once it has the control channel.
Site
One tower location of the system. Scanners show the number in decimal or hex, so both are listed.
RFSS (Radio Frequency Sub-System)
A group of sites run by the same controller. Large Project 25 systems can have several.
NAC (Network Access Code)
A hex code the site transmits. Your scanner can use it to ignore other systems on the same frequency.
Talkgroup
A virtual channel on a trunked system, such as one agency’s dispatch. Programming uses the decimal or hex number, depending on your scanner.

Common questions

What frequency does the fire department use in Wilmington?

We do not have a fire dispatch channel listed specifically for Wilmington. The county-level fire dispatch channels in the same county: Houston County Fire 154.3550 MHz, narrow FM, 192.8 PL.

Do fire departments and EMS use a trunked radio system in Wilmington?

Yes. The county-level systems that cover Wilmington are Fire and EMS talkgroups are listed for Allied Radio Matrix for Emergency Response (ARMER): 3 talkgroups. A trunking scanner is required.

What scanner do I need to listen to fire and EMS in Wilmington?

The analog conventional channels can be heard on any scanner; a trunking scanner is needed for the trunked talkgroups.

What are the control channels for trunked radio in Wilmington?

For Wilmington, start with the Spring Grove site of Allied Radio Matrix for Emergency Response (ARMER). Its control channels are 852.15 MHz. Program a control channel first; the scanner finds the voice channels from it.