Skip to content

Agram Fire and EMS Frequencies

We do not have frequencies listed specifically for Agram in Morrison County, Minnesota yet. Countywide channels for Morrison County that may also cover this area are shown below when we have them. The closest trunked radio site we have is Morrison Co. Simulcast (Allied Radio Matrix for Emergency Response (ARMER)), about 8 miles away.

About Agram Fire and EMS Frequencies

Quick answer: County-level fire dispatch that covers Agram: Morrison County Fire 154.2200 MHz, narrow FM, 123.0 PL. Trunked: Allied Radio Matrix for Emergency Response (ARMER), for example Morrison County Fire talkgroup 43040 (hex a820).

  • 2 conventional channels are analog FM, so any scanner can receive them. Enter the frequency and set the tone shown in the table.
  • Trunked radio systems that carry fire and EMS traffic here: Allied Radio Matrix for Emergency Response (ARMER): 5 talkgroups. A trunking scanner is required, and it must support the system type shown.
  • To follow a trunked system, program a control channel first. For Agram, start with the Morrison Co. Simulcast site of Allied Radio Matrix for Emergency Response (ARMER), about 8 miles away. Its control channels: 852.475, 853.1 MHz.

Data updated .

Morrison County channels that also cover Agram

Fire Dispatch

Fire Dispatch frequencies for Morrison County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Morrison County FireMorrison County Fire – Paging154.2200
In 153.8900
123.0 PLFMNWNVD602

Hospitals & Medical

Hospitals & Medical frequencies for Morrison County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Morrison County HospitalSaint Gabrial's Hospital (L. Falls)155.3850127.3 PLFMNWQBS494

Allied Radio Matrix for Emergency Response (ARMER)

Allied Radio Matrix for Emergency Response (ARMER) talkgroups
AgencyDescriptionTalkgroupHexMode
Morrison County FireCounty Fire Dispatch43040a820D
Morrison County FireMLMB Fire Administration43050a82aD
Morrison County EMSMayo EMS Dispatch43078a846D
Morrison County EMSMayo – Patient Update248866136D
Morrison County EMSHART First Responders Administration43084a84cD

Nearest trunked radio sites

Distances are measured from the center of Agram.

Morrison Co. Simulcast · Allied Radio Matrix for Emergency Response (ARMER)
RFSS 4 · Site 42 (hex 2A) · about 8 mi away
Control 852.475, 853.1
Voice 851.25, 852.1, 853.4, 855.2375, 856.9375, 857.9375, 858.9375, 859.9375
Holdingford · Allied Radio Matrix for Emergency Response (ARMER)
RFSS 4 · Site 79 (hex 4F) · NAC 401 · about 19 mi away
Control 854.6875, 856.8875
Voice 856.0875, 857.8875, 858.8875, 859.5875
Onamia · Allied Radio Matrix for Emergency Response (ARMER)
RFSS 4 · Site 81 (hex 51) · NAC 40A · about 20 mi away
Control 856.9625, 857.4625
Voice 856.4625, 857.7625, 858.4625, 858.7625
What do these numbers mean?
Control channel
The frequency your scanner listens to first. It tells the scanner where each voice call is happening, so program it before anything else.
Voice
The other frequencies the site uses for calls. A trunking scanner follows them automatically once it has the control channel.
Site
One tower location of the system. Scanners show the number in decimal or hex, so both are listed.
RFSS (Radio Frequency Sub-System)
A group of sites run by the same controller. Large Project 25 systems can have several.
NAC (Network Access Code)
A hex code the site transmits. Your scanner can use it to ignore other systems on the same frequency.
Talkgroup
A virtual channel on a trunked system, such as one agency’s dispatch. Programming uses the decimal or hex number, depending on your scanner.

Common questions

What frequency does the fire department use in Agram?

We do not have a fire dispatch channel listed specifically for Agram. The county-level fire dispatch channels in the same county: Morrison County Fire 154.2200 MHz, narrow FM, 123.0 PL.

Do fire departments and EMS use a trunked radio system in Agram?

Yes. The county-level systems that cover Agram are Fire and EMS talkgroups are listed for Allied Radio Matrix for Emergency Response (ARMER): 5 talkgroups. A trunking scanner is required.

What scanner do I need to listen to fire and EMS in Agram?

The analog conventional channels can be heard on any scanner; a trunking scanner is needed for the trunked talkgroups.

What are the control channels for trunked radio in Agram?

For Agram, start with the Morrison Co. Simulcast site of Allied Radio Matrix for Emergency Response (ARMER). Its control channels are 852.475, 853.1 MHz. Program a control channel first; the scanner finds the voice channels from it.