Skip to content

Barto Fire and EMS Frequencies

We do not have frequencies listed specifically for Barto in Roseau County, Minnesota yet. Countywide channels for Roseau County that may also cover this area are shown below when we have them. The closest trunked radio site we have is Greenbush (Allied Radio Matrix for Emergency Response (ARMER)), about 6 miles away.

About Barto Fire and EMS Frequencies

Quick answer: County-level fire dispatch that covers Barto: Roseau County Fire 154.3550 MHz, narrow FM, 114.8 PL. Trunked: Allied Radio Matrix for Emergency Response (ARMER), for example Roseau County Fire talkgroup 50907 (hex c6db).

  • 2 conventional channels are analog FM, so any scanner can receive them. Enter the frequency and set the tone shown in the table.
  • Trunked radio systems that carry fire and EMS traffic here: Allied Radio Matrix for Emergency Response (ARMER): 2 talkgroups. A trunking scanner is required, and it must support the system type shown.
  • To follow a trunked system, program a control channel first. For Barto, start with the Greenbush site of Allied Radio Matrix for Emergency Response (ARMER), about 6 miles away. Its control channels: 852.9125, 853.2625 MHz.

Data updated .

Roseau County channels that also cover Barto

Fire Dispatch

Fire Dispatch frequencies for Roseau County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Roseau County FireCounty Fire154.3550114.8 PLFMNWNPU314

Hospitals & Medical

Hospitals & Medical frequencies for Roseau County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Roseau County HospitalRoseau Area Hospital155.3250103.5 PLFMNWPJV915

Allied Radio Matrix for Emergency Response (ARMER)

Allied Radio Matrix for Emergency Response (ARMER) talkgroups
AgencyDescriptionTalkgroupHexMode
Roseau County FireCounty Fire Main50907c6dbD
Roseau County EMSCounty EMS50906c6daD

Nearest trunked radio sites

Distances are measured from the center of Barto.

Greenbush · Allied Radio Matrix for Emergency Response (ARMER)
RFSS 6 · Site 5 (hex 5) · NAC 40c · about 6 mi away
Control 852.9125, 853.2625
Voice 851.2125, 852.7375, 854.3375
Juneberry · Allied Radio Matrix for Emergency Response (ARMER)
RFSS 6 · Site 6 (hex 6) · about 11 mi away
Control 851.0375, 854.2875
Voice 851.9125, 852.1625, 853.4
Roseau · Allied Radio Matrix for Emergency Response (ARMER)
RFSS 6 · Site 7 (hex 7) · about 18 mi away
Control 851.2875, 851.7625
Voice 851.4875, 853.075, 853.2875
What do these numbers mean?
Control channel
The frequency your scanner listens to first. It tells the scanner where each voice call is happening, so program it before anything else.
Voice
The other frequencies the site uses for calls. A trunking scanner follows them automatically once it has the control channel.
Site
One tower location of the system. Scanners show the number in decimal or hex, so both are listed.
RFSS (Radio Frequency Sub-System)
A group of sites run by the same controller. Large Project 25 systems can have several.
NAC (Network Access Code)
A hex code the site transmits. Your scanner can use it to ignore other systems on the same frequency.
Talkgroup
A virtual channel on a trunked system, such as one agency’s dispatch. Programming uses the decimal or hex number, depending on your scanner.

Common questions

What frequency does the fire department use in Barto?

We do not have a fire dispatch channel listed specifically for Barto. The county-level fire dispatch channels in the same county: Roseau County Fire 154.3550 MHz, narrow FM, 114.8 PL.

Do fire departments and EMS use a trunked radio system in Barto?

Yes. The county-level systems that cover Barto are Fire and EMS talkgroups are listed for Allied Radio Matrix for Emergency Response (ARMER): 2 talkgroups. A trunking scanner is required.

What scanner do I need to listen to fire and EMS in Barto?

The analog conventional channels can be heard on any scanner; a trunking scanner is needed for the trunked talkgroups.

What are the control channels for trunked radio in Barto?

For Barto, start with the Greenbush site of Allied Radio Matrix for Emergency Response (ARMER). Its control channels are 852.9125, 853.2625 MHz. Program a control channel first; the scanner finds the voice channels from it.