About Taylor Fire and EMS Frequencies
Quick answer: County-level fire dispatch that covers Taylor: Owen County Fire/EMS 154.1450 MHz, narrow FM, 146.2 PL. Trunked: Indiana Project Hoosier SAFE-T, for example Owen County Fire talkgroup 21565 (hex 543d).
- 2 conventional channels are analog FM, so any scanner can receive them. Enter the frequency and set the tone shown in the table.
- Trunked radio systems that carry fire and EMS traffic here: Indiana Project Hoosier SAFE-T: 7 talkgroups. A trunking scanner is required, and it must support the system type shown.
- To follow a trunked system, program a control channel first. For Taylor, start with the Putnamville site of Indiana Project Hoosier SAFE-T, about 11 miles away. Its control channels: 852.925, 853.425, 853.925 MHz.
Data updated .
Owen County channels that also cover Taylor
Fire Dispatch
| Agency | Description | Frequency (MHz) | Tone | Mode | FCC |
|---|---|---|---|---|---|
| Owen County Fire/EMS | County Fire | 154.1450 In 159.2850 | 146.2 PL | FMN | KZP242 |
Fire Ground / Tactical
| Agency | Description | Frequency (MHz) | Tone | Mode | FCC |
|---|---|---|---|---|---|
| Owen County Fire/EMS | Owen Valley Fire | 154.3400 | FMN | WNVK654 |
Indiana Project Hoosier SAFE-T
| Agency | Description | Talkgroup | Hex | Mode |
|---|---|---|---|---|
| Owen County Fire | Owen County Fire – Dispatch | 21565 | 543d | D |
| Owen County Fire | Owen County Fire – Fire Ground | 21566 | 543e | D |
| Owen County Fire | Owen County Fire – Fire Ground | 21567 | 543f | D |
| Owen County Fire | Owen County Fire – Fire Ground | 21568 | 5440 | D |
| Owen County EMS | Owen County EMS – Operations | 21561 | 5439 | D |
| Owen County EMS | Owen County EMS – Operations | 21562 | 543a | D |
| Owen County EMS | Owen County EMS – Operations | 21563 | 543b | D |
Nearest trunked radio sites
Distances are measured from the center of Taylor.
What do these numbers mean?
- Control channel
- The frequency your scanner listens to first. It tells the scanner where each voice call is happening, so program it before anything else.
- Voice
- The other frequencies the site uses for calls. A trunking scanner follows them automatically once it has the control channel.
- Site
- One tower location of the system. Scanners show the number in decimal or hex, so both are listed.
- RFSS (Radio Frequency Sub-System)
- A group of sites run by the same controller. Large Project 25 systems can have several.
- NAC (Network Access Code)
- A hex code the site transmits. Your scanner can use it to ignore other systems on the same frequency.
- Talkgroup
- A virtual channel on a trunked system, such as one agency’s dispatch. Programming uses the decimal or hex number, depending on your scanner.
Common questions
What frequency does the fire department use in Taylor?
We do not have a fire dispatch channel listed specifically for Taylor. The county-level fire dispatch channels in the same county: Owen County Fire/EMS 154.1450 MHz, narrow FM, 146.2 PL.
Do fire departments and EMS use a trunked radio system in Taylor?
Yes. The county-level systems that cover Taylor are Fire and EMS talkgroups are listed for Indiana Project Hoosier SAFE-T: 7 talkgroups. A trunking scanner is required.
What scanner do I need to listen to fire and EMS in Taylor?
The analog conventional channels can be heard on any scanner; a trunking scanner is needed for the trunked talkgroups.
What are the control channels for trunked radio in Taylor?
For Taylor, start with the Putnamville site of Indiana Project Hoosier SAFE-T. Its control channels are 852.925, 853.425, 853.925 MHz. Program a control channel first; the scanner finds the voice channels from it.