Skip to content

Liberty Fire and EMS Frequencies

We do not have frequencies listed specifically for Liberty in Shelby County, Indiana yet. Countywide channels for Shelby County that may also cover this area are shown below when we have them. The closest trunked radio site we have is Shelby Co Simulcast (Indiana Project Hoosier SAFE-T), about 8 miles away.

About Liberty Fire and EMS Frequencies

Quick answer: County-level fire dispatch that covers Liberty: Shelby County Fire 154.1600 MHz, narrow FM, 167.9 PL. Trunked: Indiana Project Hoosier SAFE-T, for example Shelby County Fire talkgroup 12204 (hex 2fac).

  • 3 conventional channels are analog FM, so any scanner can receive them. Enter the frequency and set the tone shown in the table.
  • Trunked radio systems that carry fire and EMS traffic here: Indiana Project Hoosier SAFE-T: 3 talkgroups. A trunking scanner is required, and it must support the system type shown.
  • To follow a trunked system, program a control channel first. For Liberty, start with the Shelby Co Simulcast site of Indiana Project Hoosier SAFE-T, about 8 miles away. Its control channels: 851.9375, 853.9375 MHz.

Data updated .

Shelby County channels that also cover Liberty

Fire Dispatch

Fire Dispatch frequencies for Shelby County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Shelby County FireShelby County Fire – Dispatch154.1600167.9 PLFMNKNCK900

Fire Ground / Tactical

Fire Ground / Tactical frequencies for Shelby County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Shelby County FireShelby County Fire – Tactical Channel (South of St Rd 44)154.2050167.9 PLFMNKDG917
Shelby County FireShelby County Fire – Tactical Channel (North of St Rd 44)154.2200FMNWNQG623

Indiana Project Hoosier SAFE-T

Indiana Project Hoosier SAFE-T talkgroups
AgencyDescriptionTalkgroupHexMode
Shelby County FireCounty Fire/EMS – Operations122042facD
Shelby County FireCounty Fire/EMS – Dispatch (Alerts only)122052fadD
Shelby County HospitalCounty Hospital Operations122182fbaD

Nearest trunked radio sites

Distances are measured from the center of Liberty.

Shelby Co Simulcast · Indiana Project Hoosier SAFE-T
RFSS 1 · Site 5 (hex 5) · NAC 6B5 · about 8 mi away
Control 851.9375, 853.9375
Voice 851.0625, 851.4375, 852.0625, 852.3125, 852.75, 853.75
Greensburg · Indiana Project Hoosier SAFE-T
RFSS 2 · Site 46 (hex 2E) · NAC 6B4 · about 14 mi away
Control 852.9125, 853.4125
Voice 851.4125, 851.9125, 853.1875
Rushville · Indiana Project Hoosier SAFE-T
RFSS 1 · Site 76 (hex 4C) · NAC 6B9 · about 15 mi away
Control 852.9625, 853.4625
Voice 851.4875, 851.9625, 852.4625
What do these numbers mean?
Control channel
The frequency your scanner listens to first. It tells the scanner where each voice call is happening, so program it before anything else.
Voice
The other frequencies the site uses for calls. A trunking scanner follows them automatically once it has the control channel.
Site
One tower location of the system. Scanners show the number in decimal or hex, so both are listed.
RFSS (Radio Frequency Sub-System)
A group of sites run by the same controller. Large Project 25 systems can have several.
NAC (Network Access Code)
A hex code the site transmits. Your scanner can use it to ignore other systems on the same frequency.
Talkgroup
A virtual channel on a trunked system, such as one agency’s dispatch. Programming uses the decimal or hex number, depending on your scanner.

Common questions

What frequency does the fire department use in Liberty?

We do not have a fire dispatch channel listed specifically for Liberty. The county-level fire dispatch channels in the same county: Shelby County Fire 154.1600 MHz, narrow FM, 167.9 PL.

Do fire departments and EMS use a trunked radio system in Liberty?

Yes. The county-level systems that cover Liberty are Fire and EMS talkgroups are listed for Indiana Project Hoosier SAFE-T: 3 talkgroups. A trunking scanner is required.

What scanner do I need to listen to fire and EMS in Liberty?

The analog conventional channels can be heard on any scanner; a trunking scanner is needed for the trunked talkgroups.

What are the control channels for trunked radio in Liberty?

For Liberty, start with the Shelby Co Simulcast site of Indiana Project Hoosier SAFE-T. Its control channels are 851.9375, 853.9375 MHz. Program a control channel first; the scanner finds the voice channels from it.