Skip to content

Cedar Hill Fire and EMS Frequencies

We do not have frequencies listed specifically for Cedar Hill in Robertson County, Tennessee yet. Countywide channels for Robertson County that may also cover this area are shown below when we have them. The closest trunked radio site we have is Adams (Tennessee Advanced Communications Network (TACN)), about 4 miles away.

About Cedar Hill Fire and EMS Frequencies

Quick answer: County-level fire dispatch that covers Cedar Hill: Robertson County Fire 154.3850 MHz, narrow FM, 131.8 PL. County-level ems dispatch that covers Cedar Hill: Robertson County EMS 155.2350 MHz, narrow FM, 110.9 PL.

  • 4 conventional channels are analog FM, so any scanner can receive them. Enter the frequency and set the tone shown in the table.
  • 1 conventional channel uses a digital mode (NXDN48), which needs a scanner that decodes that mode.

Data updated .

Robertson County channels that also cover Cedar Hill

Fire Dispatch

Fire Dispatch frequencies for Robertson County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Robertson County FireRobertson County Fire – Dispatch (Orlinda Multicast)154.3850131.8 PLFMNWPIB268
Robertson County Fire UnconfirmedRobertson County Fire – Dispatch (Greenbriar Multicast)154.9800
In 156.0000
173.8 PLFMNWPMP988
Robertson County FireRobertson County Fire – Dispatch (Cross Plains Multicast)155.6550
In 153.8000
114.8 PLFMNKNNJ505

EMS Dispatch

EMS Dispatch frequencies for Robertson County
AgencyDescriptionFrequency (MHz)ToneModeFCC
Robertson County EMSRobertson County EMS – Dispatch155.2350110.9 PLFMNKGL631
Robertson County EMS BackupRobertson County EMS – Dispatch (to trunked System)460.6375
In 465.6375
RAN 21NXDN48WNAV319

Nearest trunked radio sites

Distances are measured from the center of Cedar Hill.

Adams · Tennessee Advanced Communications Network (TACN)
RFSS 1 · Site 50 (hex 32) · NAC 2A3 · about 4 mi away
Control 769.10625, 770.58125
Voice 769.43125, 770.05625, 771.23125, 771.50625
Springfield · Tennessee Advanced Communications Network (TACN)
RFSS 1 · Site 35 (hex 23) · NAC 2A5 · about 9 mi away
Control 851.7125, 852.0625
Voice 852.3875, 852.75, 853.5, 853.8
E Robertson HS/Cross Plains · Tennessee Advanced Communications Network (TACN)
RFSS 1 · Site 34 (hex 22) · about 16 mi away
Control 769.50625, 771.11875
Voice 771.78125, 772.15625, 772.83125, 773.20625
What do these numbers mean?
Control channel
The frequency your scanner listens to first. It tells the scanner where each voice call is happening, so program it before anything else.
Voice
The other frequencies the site uses for calls. A trunking scanner follows them automatically once it has the control channel.
Site
One tower location of the system. Scanners show the number in decimal or hex, so both are listed.
RFSS (Radio Frequency Sub-System)
A group of sites run by the same controller. Large Project 25 systems can have several.
NAC (Network Access Code)
A hex code the site transmits. Your scanner can use it to ignore other systems on the same frequency.
Talkgroup
A virtual channel on a trunked system, such as one agency’s dispatch. Programming uses the decimal or hex number, depending on your scanner.

Common questions

What frequency does the fire department use in Cedar Hill?

We do not have a fire dispatch channel listed specifically for Cedar Hill. The county-level fire dispatch channels in the same county: Robertson County Fire 154.3850 MHz, narrow FM, 131.8 PL.

What frequency does EMS or the ambulance service use in Cedar Hill?

We do not have a EMS dispatch channel listed specifically for Cedar Hill. The county-level EMS dispatch channels in the same county: Robertson County EMS 155.2350 MHz, narrow FM, 110.9 PL.

What scanner do I need to listen to fire and EMS in Cedar Hill?

The analog conventional channels can be heard on any scanner; a scanner that decodes NXDN48 is needed for the digital conventional channels.

What are the control channels for trunked radio in Cedar Hill?

For Cedar Hill, start with the Adams site of Tennessee Advanced Communications Network (TACN). Its control channels are 769.10625, 770.58125 MHz. Program a control channel first; the scanner finds the voice channels from it.