Skip to content

How to Program a Trunked Radio System Into Your Scanner

Program the site's control channels first, then add the talkgroups you want. Pick the site nearest you, set the right system type, and use decimal or hex to match your scanner.

Before you start

You need three things from a county or city page on this site:

  1. The system type, such as P25 Phase I, P25 Phase II, Motorola Type II, DMR or NXDN. Your scanner must support it. See conventional, trunked and digital.
  2. A site that reaches your location, with its control channels.
  3. The talkgroups you want to hear.

Every scanner menu is different, so this guide uses the general steps. Your scanner's manual or its programming software has the exact button presses.

Step 1: Pick the site

A trunked system has many towers. Choose the one that covers where you will listen.

  • On a county page, the site cards list each site's name and control channels. A city page may show the nearest sites to the town.
  • If two sites are near you, program both. Your scanner will lock to whichever is stronger.
  • If you are travelling, program the sites along your route, or use a scanner that picks sites by location.

Step 2: Create the system

In your scanner or its software, add a new trunked system.

  • Set the system type to match the listing.
  • Give it a name you will recognise, for example the system and county.
  • Leave the NAC on automatic unless you have a reason to set it. See what NAC and RFSS mean.

Step 3: Add the site and its control channels

Add a site to the system and enter every control channel from the listing. Frequencies are in MHz, for example 851.7375.

  • Enter all of them, not just the first. A site can move its control channel to another frequency on its list.
  • Enter the control frequencies only. The voice frequencies are found by your scanner from the control channel.

Step 4: Add talkgroups

Add the talkgroups you want to hear, using the talkgroup number from the listing.

  • Check whether your scanner wants decimal or hex. We show both, so copy the right one. Entering a decimal number in a hex field will point you at the wrong talkgroup.
  • Give each talkgroup a short label, such as the alpha tag.
  • For fire and EMS, a good start is your own area's dispatch talkgroups, then the matching fireground or tactical talkgroups. See dispatch and fireground channels.
  • Skip talkgroups that carry the Enc badge. They are encrypted and will be silent. See encrypted fire and EMS radio.

Start small. Choosing a few dispatch talkgroups is better than enabling hundreds and listening to a busy system you don't need.

Step 5: Test it

Switch to the system and scan. You should see the scanner lock onto a control channel within a few seconds, then hear calls on the talkgroups you enabled.

Quiet talkgroups can take a while to produce a call, and a small fire department may go hours without one. Test on a busy dispatch talkgroup during the day, when more people are working. See why a fire channel is quiet.

If you hear nothing

SymptomLikely cause
The scanner never finds the control channelYou are out of range of that site, or the frequencies were entered wrong
It locks, but hears no callsThe talkgroups are wrong, or you used decimal where hex was needed
You hear calls but they are garbled or silentThe talkgroup is encrypted, or the system is Phase II and your scanner is not
You hear a different systemTwo systems share a frequency. Set the NAC to the listed value
It worked and then stoppedThe system changed. See why a fire frequency stopped working

Tips

  • Signal first. A trunked system needs a decent control channel signal. An outside or higher antenna helps more than any setting.
  • Keep a short list. One site, a few talkgroups, and add more once it works.
  • Check the date. Systems are re-programmed. If a talkgroup goes quiet for weeks, check whether it moved.

Frequently asked questions

Do I need to enter every voice frequency?

No. Enter the control channels only. Your scanner learns the voice frequencies from the control channel.

What if I live between two sites?

Program both. A scanner follows the one it can hear best.

Can I use the same talkgroups on every site?

Usually yes. A talkgroup belongs to the system, not to a tower, so the same number works on any site that carries it.

Why do some talkgroups show no audio?

They may be encrypted, quiet at that time of day, or not carried on the site you chose.