Skip to content

Why a Fire or EMS Frequency Stopped Working

The usual reasons are that the department moved to a trunked or digital system, encrypted the channel, kept the frequency only as a backup, or your scanner settings no longer match. Check the listing's status badge first.

The short version

A fire or EMS frequency that used to work and now doesn't has usually changed in one of a few ways. Work through the list in order, from the cheapest check to the biggest change. First make sure it is not just a quiet channel, because fire channels are often silent between calls.

1. Check the status badge

Listings on this site mark entries that aren't fully current. A badge such as Expired, Old, Backup or Unconfirmed next to an agency tells you the entry may not carry live traffic.

  • Expired means the license for the frequency has lapsed. It may still be used, but it is not confirmed.
  • Old means the source describes it as a former frequency.
  • Backup means it is a spare or fallback channel, so it is mostly quiet.
  • Unconfirmed means the source marks the entry as uncertain.

2. Check your scanner settings

Most "dead" frequencies are a settings problem.

  • Mode. FM, narrow FM (FMN), AM and the digital modes are different. The wrong one gives silence or noise. See conventional, trunked and digital.
  • Tone. An entered PL or DPL tone that doesn't match will keep the squelch closed. Turn the tone off to test. See what the tone codes mean.
  • Frequency. A transposed digit is easy to make. Check it against the listing.
  • Range. A weak signal can look like a dead channel. Try a different location or antenna.

3. The department moved to a trunked system

Many fire departments and EMS agencies have retired their conventional channels and joined a shared trunked system. The old frequencies go quiet, and the traffic is on a talkgroup instead.

  • Look at your county page. If a trunked system is listed for the department, its dispatch has probably moved there.
  • You need a trunking scanner and the system's site and talkgroups. See how to program a trunked system.

4. The department moved to digital

A conventional channel can switch from analog to a digital mode such as P25. An analog-only scanner will hear nothing on a digital channel. If the listing shows a digital mode, you need a scanner that decodes it.

5. The channel is now encrypted

If you can see activity but hear nothing, the channel may have been encrypted. It looks active on a trunked system and can still be silent. See encrypted fire and EMS radio.

6. Narrowbanding

In the US, the FCC required most VHF and UHF public safety radios to move from 25 kHz channels to 12.5 kHz channels by January 1, 2013. An older entry that was set to wide FM may now be narrow FM (FMN). A scanner set to the wrong width sounds weak or distorted.

7. Departments merged or the system was re-planned

Fire districts consolidate, dispatch centres merge, and radio systems are re-planned: frequencies are re-assigned, sites are added or removed, and talkgroups are renumbered. When that happens, a scanner programmed from older data goes quiet even though the system is still working.

What to do next

  1. Re-check the page for the area. Data on this site is updated as sources change.
  2. Turn the tone off and try the mode alternatives.
  3. Look for a trunked system or an Enc badge.
  4. If the listing looks wrong, tell us. Use the link below, and include the frequency, the place and what you hear.

Frequently asked questions

Why does my scanner show activity but no sound?

Most often the channel is encrypted. The scanner detects the signal but can't decode the voice.

Did the frequency stop being used?

Possibly. Departments retire channels when they join a shared system, but they sometimes keep a backup. A Backup badge means the entry is a fallback.

What is narrowbanding?

It is the FCC requirement that older 25 kHz channels be changed to 12.5 kHz. It affects how a conventional channel should be set on a scanner.

How current is this site?

Each page's listing shows its status. We update as sources change, but radio systems can change without notice, so verify on your own scanner.